CAMERA LINK FC300ACL Скачать руководство пользователя страница 25

Страница: 25 / 36

N10316;25/36

- 25 -

●

● Camera Operation Mode

Camera Operation Mode

/ Asynchronous Shutter

・

Preset Shutter

・

V reset ON

In this mode, the exposure is conducted synchronizing with the trigger pulse. The camera exposure starts at the rising edge of the

trigger signal and the exposure time will be the preset value of the electronic shutter.. .

If the next pulse is receipt during the video out period, the image signal is swept out in midstream and can’t normally get image

signal,

500ms

Next VD

Trigg er sign al

(Positive)

Int ernal VD

CCD exposure

Vid eo out

Camera op er ation

mode

Continuou s shutt er

Continuous shutter

Asynchronous shutt er

Automati cally switch to the continuous

shuut er mod e if the pulse width of the

trigger sign al is more than 500msec..

Exposure time

Sweep charg e

* The camera does not switch to continuous shutter mode when the low speed shutter is selected.

* It is V reset at the next internal VD timing immediately after the exposure is finished.

* The exposure time is the preset value of the electronic shutter.

* When switched to asynchronous shutter mode from continuous shutter mode, the waiting period of at least 1VD is required if the

shutter speed is less than 1 VD.

●

● H Reset Mode

H Reset Mode

By selecting this “H Reset Mode”, the camera automatically holds the

actual activation of trigger until the next horizontal blanking period. Then

the SUB pulse is activated during the horizontal blanking period and the

noise in image can be avoided.

ＨＤ

Normal SUB pulse timing

SUB pulse

Trigg er pulse

(High-tru e logi c)

Intern al HD

CCD exposure

Vid eo out

Содержание FC300ACL





































Результаты поиска

Содержание FC300ACL

Отзывы:

Похожие инструкции для FC300ACL

Бренды по названию

Популярные бренды

CAMERA LINK FC300ACL, Инструкция по эксплуатации

Результаты поиска

Содержание FC300ACL

Отзывы:

Похожие инструкции для FC300ACL

Бренды по названию

Популярные бренды