K12703 ; 25/43
- 25 -
MS=A SS=7
MS=A SS=7
ID: CAMERA-1
CAMERA TYPE
ID not specified
ID specified
* M E N U
4
M E N U
:
O N
P A T T E R N :
O F F
b i t
:
8
b i t
F O R M
:
D U A L
-
:
( R e s e r v e d )
V S U B
:
1 1 5 = H ' 7 3
M S = C
S S = 7
M F = 0 0 0 1 . 0 0 0 8 . 0 0 0 0
C A M E R A
T Y P E
[ V . X . X X ]
Menu4 display
* M E N U
5
M E N U
:
O N
S O R T
:
O N
R E P T
:
O F F
-
:
( R e s e r v e d )
-
:
( R e s e r v e d )
M S = C
S S = 7
M F = 0 0 0 1 . 0 0 0 8 . 0 0 0 0
C A M E R A
T Y P E
[ V . X . X X ]
Menu
5
display
<MENU4> Displayed contents
PATTERN: ON /OFF state of the test pattern output is displayed.
bit:
Bit format (8/10 bit) for image output is displayed.
FORM: CCD output system (QUAD/DUAL/SINGLE) is displayed.
VSUB:
The setting value of Vsub voltage (substrate voltage of CCD
element) is displayed. Since the value is optimally set before
shipment, the user is not required to change it as a general
rule.
<MENU5> Displayed contents
SORT: Whether the vertical line sorting in QUAD is enabled (ON) or
disabled (OFF) is displayed.
REPT:
Whether the continuous output of image signal in the
asynchronous shutter mode is enabled (ON) or disabled
(OFF) is displayed.
* The following items are for display only; they cannot be directly changed
on the menu. These are automatically updated when a corresponding
change is made by the switch.
MS= The current position of the mode switch is displayed.
SS= The current position of the shutter setting switch (EXP.) is displayed.
MF= The information(32/16 bit) of the internal mode flags of the camera
(internal flags to determine operation) is displayed in the hexadecimal system.
The details of the internal flags are described later.
Tc= The current internal temperature of the camera is displayed in Celsius.
The temperature data are refreshed every 0.4 seconds.
[Display of ID information]
The ID code and other information set by the user for each camera can be
stored in the camera (The setting is executed through the serial
communication.). The settable maximum number of characters are 15, and
alphabets (both upper and lower cases), numbers and some special
symbols such as
”+” and “-” excluding the control codes can be used.
Set ID code can be confirmed as it is displayed on the lower left of
“MENU display of set Group 1” (On screen display)
(When ID code is not set, the camera type is displayed.)
The right figures shows the display example setting
“CAMERA-1” as ID information.
●
Confirmation of changed settings by menu
They can also be changed by serial communication command confirming the currently displaying menu contents.
Each time the settings of each menu item are changed, display contents is updated.
(6-8) Description of operation mode and functional limitation
[Scanning mode]
● Description of scan mode
This camera has the normal scan mode only:
Scan mode
Operation
Frame rate
Normal scan mode (NORMAL) Readout of all 2.07 megapixels
60 fps(QUAD)
●
Normal scan mode ···· The image of all effective pixels is read out at a frame rate of 60 Hz (QUAD).
● Functional limitation by scan mode
Usable functions vary by the scan mode that is currently selected.
The functions marked with
○ in the following table are usable and those marked with × are not usable.
(Note) Carefully note that the operation is not guaranteed if an unusable function is selected.
(Note) Caution is required especially when control is executed using the write commands for the flag register among the
serial communication commands because the incompatibility between the selected scan mode and the selected
function is not warned. Setting of an inappropriate parameter results in operation failure.
Current scan mode
No shutter Continuous shutter Asynchronous shutter
Low speed shutter
Normal scan mode (NORMAL)
O
O
O
O
