background image

OPERATION - ELECTRONIC CONTROL UNIT

The electronic control unit (4), which is mounted inside your caravan, is responsible for controlling the 

manoeuvring system. 

The control unit has three LED’s, one pushbutton and one slide switch (Fig. 

14

): 

Green LED (Fig. 

14

B): Power LED continuously illuminated

 

when system is activated (by moving slide switch 

to “On”-I). If the handset far away from the control unit, beyond the availably distance, this LED will go out. 

Blue LED (Fig. 

14

C): Error message LED concerning caravan battery: 

Blue LED is blinking (2 times blinking, break, 2 times blinking, break etc.): Battery voltage too low (<10V).

Battery needs to be recharged. 

Blue LED is blinking (4 times blinking, break, 4 times blinking, break etc.): Battery Voltage too high (over

charged). Try to discharge the battery by turning on a user (for example a lamp or water-pump). 

Red LED (Fig. 

14

D) is blinking (6 times blinking, break, 6 times blinking, break etc.): Amp overload protection 

is activated. Wait about 60 seconds and try again. 

In general all error messages will reset automatically after one minute. If this is not the case, reset the 

electronics of the manoeuvring system by switching off the system via the isolation switch and the remote 

control handset for at least 15 seconds and then turning it on again. 

The Reset Button (Fig. 

14

A): The remote control handset and the control unit are synchronised with each 

other in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised 

as described below: 

Ref: 

ELITE

PRO

 

EM30

5

-

0814

-Rev.A. 

CAMEC

 

ELITE

 PRO

 

EM30

5

Ref: 

ELITE

 PRO

 

EM30

5

-

0814

-Rev.A. 

CAMEC

 

ELITE

 PRO

 

EM30

5

1

5

Check the installation in accordance with the installation instructions and ensure that the drive rollers are

not applied. Check that the battery is properly connected, check the condition of the battery and that a

voltage of 12 V is present at the control unit.

Please ensure that the battery isolation switch is on.

Activate the remote control handset by sliding the slide switch to “On”-I (Fig. 

4

A). The green LED on the

remote control handset (Fig. 

4

H) starts to flash slowly.

Press the reset button (Fig. 

4

A) on the control unit. All three LED’s on the control unit (Fig. 3B, 3C & 3D)

will flash slowly.

Press both forwards (Fig. 

4

B) and reverse (Fig. 

4

C) button on the remote control handset for about 3

seconds. Then the handset buzzer will give a short beep to confirm that the synchronisation is complete.

After successful synchronisation, the green LED on the control unit (Fig. 

4

B) and on the remote control

handset (Fig. 

4

H) will illuminate continuously.

The single-twin axle function switch (Fig. 

14

S/T): The 

Camec Elite Pro

®

 EM305 Caravan manoeuvring 

system is suitable for both single axle and twin axle caravans. You just need to 

move

 the single-twin axle 

function switch (Fig 

14

S/T) on the control unit, so that the manoeuvring system can be used for a single-

axle caravan or a twin-axle caravan (for 2 motor use but also for 4 motor use). In the twin axle function 

the all wheels will drive but at a different speed.  

The switch standard pre-selected for single axle use (Fig 

14

S). For twin axle use, just move the switch to the 

twin axle position (Fig. 

14

T). When move the single-twin axle function switch, the battery power isolation 

switch (29) must be turned off. 

OPERATION - GETTING STARTED

Please make sure you read the safety instructions very carefully and make sure that you 

follow these guidelines! 

Make sure that the battery that supplies the system is fully charged and in good condition. 

Make sure that the caravan is free from the vehicle and the handbrake is on. Also make sure 

that the corner steady feet are fully raised. 

Turn on the battery power isolation switch (29). 

Activate the manoeuvring system by move slide switch to “On”-I on the remote control (Fig. 

4

A). The green 

LED (Fig. 

4

H) on the remote control handset will illuminate and you will hear a short beep. The remote control 

is ready for use. 

To activate the system press the two 

(Fig. 

4

I)

 buttons for three seconds

. The blue LED (Fig. 

4

H) will blink fast 

during these three seconds and every second there will be a beep. This warns you that the system will be 

activated! 

Before operating the manoeuvring system, release the handbrake. 

“More information https://www.caravansplus.com.au"

Содержание ELITE PRO EM305




















Отзывы: