background image

Page 

8

 - Manual 

FA01625-EN

  - 02/2023 - © C

AME S.p.A. - The contents of this manual may be changed at any time and without notice. - T

ranslation of the o

riginal instructions

Cable types and minimum thicknesses

Cable length (m)

up to 20

from 20 to 30

Power supply 230 V AC

3G x 1.5 mm²

3G x 2.5 mm²

Power supply 120 V AC

3G x 1.5 mm²

3G x 2.5 mm²

24 V AC/DC flashing beacon

2 x 1 mm²

2 x 1 mm²

TX Photocells

2 x 0.5 mm²

2 x 0.5 mm²

RX photocells

4 x 0.5 mm²

4 x 0.5 mm²

Command and control devices

*no. x 0.5 mm²

*no. x 0.5 mm²

* no. = see product assembly instructions - Warning: the cable cross-section is indicative and varies according to the motor power and cable length.

 To connect the antenna, use RG58 cable (up to 5 m).

 For installation in an outdoor environment, use cables with properties at least equivalent to those of type H05RN-F (with designation 60245 IEC 57).

 For installation in an indoor environment, use cables with properties at least equivalent to those of type H05VV-F (designation to 60227 IEC 53).

 If the cable lengths differ from those specified in the table, define the cable cross-sections according to the actual power draw of the connected devices and in 

line with regulation CEI EN 60204-1.

 For multiple, sequential loads along the same line, recalculate the values in the table according to the actual power draw and distances. For information on 

connecting products not covered in this manual, please see the documentation accompanying the products themselves.

 For paired and CRP connection, use a UTP CAT5 cable. Maximum length 1000 metres.

Содержание GARD G6000

































Отзывы: