Page
3
- Manual
FA01625-EN
- 02/2023 - © C
AME S.p.A. - The contents of this manual may be changed at any time and without notice. - T
ranslation of the o
riginal instructions
GENERAL PRECAUTIONS FOR INSTALLERS
Important safety instructions.
Please follow all of these instructions. Improper installation may cause serious bodily harm.
Before continuing, please also read the general precautions for users.
Only use this product for its intended purpose. Any other use is hazardous. • The manufacturer cannot be held liable for any
damage caused by improper, unreasonable or erroneous use. • This product is defined by the Machinery Directive (2006/42/EC)
as partly completed machinery. • Partly completed machinery means an assembly which is almost machinery but which cannot
in itself perform a specific application. • Partly completed machinery is only intended to be incorporated into or assembled with
other machinery or other partly completed machinery or equipment thereby forming machinery to which the Machinery Directive
(2006/42/EC) applies. • The final installation must comply with the Machinery Directive (2006/42/EC) and the European reference
standards in force. • The manufacturer declines any liability for using non-original products, which would also void the warranty.
• All operations indicated in this manual must be carried out exclusively by skilled and qualified personnel and in full compliance
with the regulations in force. • The device must be installed, wired, connected and tested according to good professional practice,
in compliance with the standards and laws in force. • Make sure the mains power supply is disconnected during all installation
procedures. • Check that the temperature ranges given are suitable for the installation site. • Make sure that opening the automatic
barrier does not constitute a hazard. • Do not install on slopes i.e. any surfaces that are not perfectly level. • Do not install the
operator on surfaces that could yield and bend. If necessary, add suitable reinforcements to the anchoring points. • Make sure
that no direct jets of water can wet the product at the installation site (sprinklers, water cleaners, etc.). • Make sure you have set
up a suitable dual-pole cut-off device along the power supply that is compliant with the installation rules. It should completely cut
off the power supply according to category III surcharge conditions. • Demarcate the entire site properly to prevent unauthorised
personnel from entering, especially minors. • In case of manual handling, have one person for every 20 kg that needs hoisting;
for non-manual handling, use proper hoisting equipment in safe conditions. • When the operator is being fixed in place, it may be
unstable and overturn. Be careful and do not lean on it until it is fully fastened in place. • Use suitable protection to prevent any
mechanical hazards due to persons loitering within the operating range of the operator. • The electrical cables must pass through
special pipes, ducts and cable glands in order to guarantee adequate protection against mechanical damage. • Make sure that the
moving mechanical parts are suitably far away from the wiring. • The electrical cables must not touch any parts that may overheat
during use (such as the motor and transformer). • All fixed controls must be clearly visible after installation, in a position that allows
the guided part to be directly visible, but far away from moving parts. In the case of a hold-to-run control, this must be installed at
a minimum height of 1.5 m from the ground and must not be accessible to the public. • If the passage is wider than 3 m, you must
use a fixed support for the boom. • If not already present, apply a permanent tag that describes how to use the manual release
mechanism close to it. • Make sure that the operator has been properly adjusted and that the safety and protection devices and the
manual release are working properly. • Before handing over to the final user, check that the system complies with the harmonised
standards and the essential requirements of the Machinery Directive (2006/42/EC). • Any residual risks must be indicated clearly
with proper signage affixed in visible areas, and explained to end users. • Put the machine’s ID plate in a visible place when the
installation is complete. • If the power supply cable is damaged, it must be immediately replaced by the manufacturer or by an
authorised technical assistance centre, or in any case, by qualified staff, to prevent any risk. • Keep this manual inside the technical
folder along with the manuals of all the other devices used for your automation system. • Make sure to hand over to the end user
all the operating manuals of the products that make up the final machinery. • The product, in its original packaging supplied by
the manufacturer, must only be transported in a closed environment (railway carriage, containers, closed vehicles). • If the product
malfunctions, stop using it and contact customer services at https://www.came.com/global/en/contact-us or via the telephone
number on the website. • The manufacture date is provided in the production batch printed on the product label. If necessary,
contact us at https://www.came.com/global/en/contact-us. • The general conditions of sale are given in the official CAME price
lists.
