CAMBRIDGE CSW-15AT Скачать руководство пользователя

Страница: 5 / 14

1.3 Numeric Entries:

Once you have entered Setup and Calibration mode, (as described on the previous

page) some entries may require entering a numeric value.

To enter a numeric value:

Press and release the

lb/kg

key to move into the desired menu field.

Press and release the

ZERO

key, the first digit will begin to flash.

Use the up and down arrow keys to increase or decrease the value of this
digit until you reach the desired value.

Press the

TARE

key to move to the next digit and repeat step 3.

When you are satisfied with the value of each digit press the

PRINT/ENTER

key to

save your entry and return to the menu.

1.4 Setup Parameters:

To begin press and hold this key until the Parameter (

P xxx

) Event counter is displayed,

then release. Immediately after

CodE

is displayed, enter in sequence (within 5 seconds)

TARE

lb/kg

GRS/NET

, and

PRINT/ENTER

. The display will indicate

ScAlE

and you are now in Setup

& Calibration mode.

Note: P xxx and C xxx are event counters that will increment each time one or more
Changes are made to the scale Scale or Calibration Parameters.

With the display indicating

ScAlE

, press the

GRS/NET

key to move down to change a

parameter. This allows the operator to change any one of the Scale Parameters S1 thru S18. For
example, press the

GRS/NET

key to move down until

is displayed,

is used to set the

capacity of the scale. Press the

lb/kg

key to move right into the

parameter. The current capacity

will be displayed. Press the

ZERO

key; the first digit will begin flashing. Enter the new capacity

using the steps described in section 1.4 shown at the top of the page. Once you have the capacity
entered, press the

PRINT/ENTER

key to enter the value and return to

The same steps can be followed to enter the count by. Press the

GRS/NET

key to move

down until S3 is displayed. Press the

lb/kg

key to move right into the

parameter. The current

Count By will be displayed. Use the up and down arrow keys to increase or decrease the value.
Use the left and right arrow keys to adjust the decimal point. When the desired Count By is
entered, press the

PRINT/ENTER

key to enter the value and return to

Содержание CSW-15AT















Результаты поиска

Содержание CSW-15AT

Отзывы:

Похожие инструкции для CSW-15AT

Бренды по названию

Популярные бренды

CAMBRIDGE CSW-15AT, Инструкции по установке, настройке и эксплуатации

Результаты поиска

Содержание CSW-15AT

Отзывы:

Похожие инструкции для CSW-15AT

Бренды по названию

Популярные бренды