CAMBRIDGE CSW-15AT Скачать руководство пользователя

Страница: 13 / 14

5.0 TESTING PROCEDURES

5.1 Testing Menu Definitions:

T1 Software

Displays the software version. Press

PRINT/ENTER

to exit.

Version

T2 Display

Flashes all display segments then all indicating Enunciators.

Press

PRINT/ENTER

to exit.

T3 Keys

Press the

ZERO

key, b1 will be displayed.

Press the

GRS/NET

key, b2 will be displayed.

Press the

TARE

key, b3 will be displayed.

Press the

lb/kg

key, b4 will be displayed.

Pressing the

PRINT/ENTER

will exit back to the menu

T4 A to D

Displays Raw counts where a 1mV/V signal from the scale will display
25,000 counts.

When the indicator is in angle mode, press the

GRS/NET

key

to cycle Pitch, Roll and Raw counts. Press the

PRINT/ENTER

Key to exit.

T5 Serial

Serial Communications can be verified by connecting pins 2 and 3 on the

serial port. A single character will be echoed and pass or fail will be

displayed. Press the

PRINT/ENTER

key to exit.

T6 Setup Data

Setup data will be sent out on the printer port.

T7 Default

Resets the indicator back to the factory settings. This will clear all calibration
and setup data. “r you sure?” will be displayed. Press the

TARE

key to exit

without Defaulting, or press the

PRINT/ENTER

key to reset the indicator to

the factory default settings.

Содержание CSW-15AT















Результаты поиска

Содержание CSW-15AT

Отзывы:

Похожие инструкции для CSW-15AT

Бренды по названию

Популярные бренды

CAMBRIDGE CSW-15AT, Инструкции по установке, настройке и эксплуатации

Результаты поиска

Содержание CSW-15AT

Отзывы:

Похожие инструкции для CSW-15AT

Бренды по названию

Популярные бренды