CAMBRIDGE CSW-15AT Скачать руководство пользователя страница 10

Страница: 10 / 14

3.0 CALIBRATION PROCEDURE

3.1 Calibration Menu Definitions:

C1 Zero All

Raw counts, (Pitch and Roll if in angle mode) will be

displayed. When

ZERO

is pressed an analog zero is done

and all calibration span points will be cleared.
If the indicator is in angle mode the Pitch and Roll offsets
will also be Zeroed.

C2 Zero

Zeroed raw counts, (Pitch and Roll if in angle mode) will be

displayed. When

ZERO

is pressed an analog zero is done

and all calibration span points will NOT be cleared.

If the indicator is in angle mode the Pitch and Roll offsets
will be Zeroed.

C3 Span Point

The last Calibration weight will be displayed then the actual

weight on the scale will be displayed.

If you do not wish to change the span point, press the

TARE

key to exit without making any changes

If the displayed weight does not match the known test

weight, use the numeric keypad to enter the correct weight.
Press the

PRINT/ENTER

key to save and exit. The display

will return to C3.

C4-C7 Span Points

C4 to C7 are for linearity correction. They can be used in

order and in any quantity or not at all if no correction is

necessary.

C4 to C7 may be entered at any time without affecting the

  Original calibration points.
  The last calibration weight will be displayed then the actual
     weight on the scale will be displayed. If no calibration

weight has been entered at this span point “

notset

” will be

displayed then the actual weight on the scale is displayed.

If the displayed weight does not match the known test

weight, follow the steps described for C3 Span Point on
adjusting the weight and entering the value.

END

Exits back to the main menu

Содержание CSW-15AT















Результаты поиска

Содержание CSW-15AT

Отзывы:

Похожие инструкции для CSW-15AT

Бренды по названию

Популярные бренды

CAMBRIDGE CSW-15AT, Инструкции по установке, настройке и эксплуатации

Результаты поиска

Содержание CSW-15AT

Отзывы:

Похожие инструкции для CSW-15AT

Бренды по названию

Популярные бренды