manualshive.com logo in svg

Calrec Hydra2, Руководство по установке

Поделиться
Скачать
Calrec Hydra2 Скачать руководство пользователя страница 44

44 HYDRA2

 

Installation Manual

Fixed Format I/O

FIXED FORMAT I/O OVERVIEW

A range of different fixed format I/O 
boxes are available to provide the 
quantity and type of signal format 
required where it is needed.

Each type of fixed format I/O box contains 
a set number of inputs and outputs, all of 
the same type / signal format. The term 
‘fixed format’ differentiates this type of 
I/O box from modular I/O racks which can 
be custom populated with mixed signal 
formats in varying quantities.

Mounting

All Hydra2 I/O boxes are fitted with 
racking angles, designed for mounting 
into standard 19” equipment bays. 

Airflow

Units can sit, or be mounted directly on 
top of, and beneath other equipment—no 
spacing above or below is required for 
cooling. Airflow is via the side panels, 
which should be left unobstructed. 
All units, other than MADI I/O, have 
fan assisted airflow. A single, high 
specification, low noise fan is mounted 
to the right hand side panel, expelling air 
from the unit. Fans are run under-voltage 
to further increase reliability and reduce 
acoustic noise, ensuring suitability for 
locating within studios.

Power

All units are fitted internally with 2 x AC 
PSUs, each with its own IEC mains input 
connector, to provide redundancy against 
both internal PSU failure, and external AC 
mains loss. Where possible, the two IEC 
connectors / PSUs should be fed from 
separate AC sources. Units are supplied 
with IEC ‘Y-split’ cables to maintain 
redundancy by allowing both PSUs to be 
fed from a single AC outlet / cable, if that 
is all that is available.

Hydra2networkconnections

I/O boxes interface with the Hydra2 
network via rear-mounted, hot-
pluggable SFP slots to allow Cat5e 

copper, singlemode, or multimode fiber 
connectivity. All units have 2 x Hydra 
ports - a primary / normally active, and 
a secondary / backup. Port 1 of an I/O 
box should connect to a primary Hydra2 
router card, port 2 should connect to the 
secondary router card fitted in the same 
rack. Note, any fixed RJ45s (as oppose 
to pluggable SFPs) on the rear of Hydra2 
I/O boxes are not functional. 

GPIO

Most fixed format I/O units can be fitted 
with an optional GPIO card that provides 
8 inputs and 8 outputs whose functions 
are assignable by any control surface on 
the network. A range of functions can be 
assigned, including Autofader and path 

Cut/On trigger inputs, fader open/start 
and error alert outputs. 

Reset

The reset button can be used to perform a 
‘soft’ or ‘hard’ reset. 

Press RESET to perform a soft reset.

Press RESET and hold until the FAN FAIL 
LED is illuminated to perform a hard reset.

Note: Splats may be emitted from 
analog outputs during a hard reset. 
Please ensure loudspeakers are 
disconnected/powered down before 
performing a hard reset.

FRONT PANEL STATUS LED’S - NORMAL CONDITION

In normal operation, front panel LEDs should be as shown above:

•  PSU               - ON solid green
•  Fan               - OFF
•  Port 1/2 Con - ON solid yellow
•  Port 1/2 Act  - FLASH (fast) green

•  Status 1 - ON solid green
•  Status 2 - FLASH (slow) green*
•  Status 3 - FLASH (slow) green*
•  Status 4 - No function**
•  Status 5 - ON solid red
•  Status 6 - ON solid red
•  Status 7 - ON solid red
•  Status 8 - OFF

Содержание Hydra2









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды