Calimet CM-5-ACFP Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 16

Calimet CM-5-ACFP Скачать руководство пользователя страница 2

2

PRODUCT SPECS

：

Voltage Input

：

110V

Maximum output current

：

15AM

，

Fuse: AC110V 15AM

Remote control distance

：

Open space >150 Feet (50 meters)

WARNING

To reduce the risk of INJURY or DEATH:



Never let children operate or play with gate control, keep remote control
away from children.



ALWAYS keep people and objects away from gate. NO ONE SHOULD CROSS
THE PATH OF MOVING GATE.



Test gate operator monthly. The gate MUST reverse in contact with a rigid
object of reverse when an object activates the non-contact sensors. After
adjusting the force or limit of travel, reset gate operator. Failure to adjust
and reset the gate operator properly can increase the risk of INJURY or
DEATH.



Use the emergency release ONLY when gate is not moving.



KEEP GATE PROPERLY MAINTAINED. Read owner’s manual. Having a
qualified service person make repairs to gate hardware.



The entrance is for vehicles ONLY. Pedestrians MUST use separate
entrance.



SAVE THESE INSTRUCTIONS.

«
1
2
3
4
...
»

Содержание CM-5-ACFP

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды