background image

 
 
 

12

 

Use Remote Control 

Device

 

Figure 12

 

There are two modes to set Remote Control: Self-study Mode& Numeric Mode   
 

 

  Self-study code may be set up to 60 groups.   
 

A.

 

  Self-study mode corresponds to receiver in control board. Press and hold STUDY key 

for  3  seconds  until  flashing  light  turn  to  solid  bright,  press  any key on  Remote  Control  until 
STUDY light turn to flashing again, setting done. Repeat above if additional code needed.   

B.

 

Existing Codes removal. Press STUDY key and hold for 8 seconds, watching light state: 

flashing-solid-flashing, setting done. All existing Self-study codes have been removed. 

 

 

Numeric Mode 
 

A.

 

First to turn SW9 key to ON position, now control board activated. 

B.

 

Make a combination of code. On SW8, Set an 8-digi combination to match identical 8-digi 

combination on  Remote Control. Note:  each  switch could be placed on up, middle and low 
position. No limit of groups of combinations. 
C.

 

On switch SW10, KEY 1 and KEY 2 are used for 2-buttom model of remote controls. Note: if 

KEY 1 code was set corresponding with BUTTON ONE on remote control, then KEY 1 will NOT 
work with BUTTON TWO on remote control. 

 

Содержание CM-5-ACFP

















Отзывы: