INPUT
THE
SD
CARD
The
SD
oblique
angle
keeps
rightward
exposure
,
put
into
the
SD
slot
and
press
it
again
to
eject
.
03
1. Dashboard
2. Nut (5mm)
3. Spring Washer
4. Screw (5 x 25mm)
5. Screw
2
.
Insert
fingers
into
the
groove
in
the
front
of
frame
and
pul l
out
to
remove
the
frame
. (
When
reatt achi ng
the
frame
,
point
the
side
with
a
groove
dow nwards
and
attach
it
.)
3
.
Leve r
Insert
the
leve rs
sup plied
with
the
uni t
into
the
grooves
at
both
sides
of
the
uni t
and
show n
in
figure
unti l
they
click
.
Pulling
the
levers
makes
possible
to
remove
the
unit
fro m
the
dashboard
.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on
the sides of the unit
Fastening the unit to the factory
radio mounting bracket
:
1. Select a position where the screw
holes of the bracket and the
screw holes of the main unit
become aligned (are fitted), and
tighten the screws at 2 places on
each side. Use either truss screws
(5 x 5mm) or flush surface screws
(4 x 5mm)
2. Screw
3. Dashboard or Console
INSTALLATION
6. Strap
Be sure to use the strap to
secure the back of the unit in
place. The strap can be bent by
hand to the desired angle.
7. Plain Washer
2
3
2
2
1
3
(
Fig
.
3
)
Removing
the
unit
1
2
3
4
5
6
7
(
Fig
.
2
)
18
Before playing a CD, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc in the direction of the arrow.
Always insert the CD with the label side facing upwards.
If the CD is inserted with the printed side facing downwards, the device
may be damaged.
Note: If there is already a CD in the CD slot , do not try to insert a second
CD. This may damage the device.
Always hold CDs by the edge. In order to keep the CD clean do not touch
the surface. Pull out the CD as follows.
Do not attach any sticker or adhesive tape on the CD.
Do not expose the CD to direct sunlight or sources of heating.
Do not leave CDs in a car if it parked in direct sunlight as that will lead to
a considerable rise in the temperature inside the car.
Note: Do not use any solvents such as petrol or thinning agents.
Commercially
available cleaning substances of antistatic spray will
damage the device.
BEFORE
PLAYING
DISCS
Cleaning
the
CD
04
ADDITIONAL
INFORMATION
17
REAR Lch LINE OUT
REAR Rch LINE OUT
BLUE
WHITE
WHITE/BLACK
GREEN
GREEN/BLACK
RED
YELLOW
BLACK
GREY
GREY/BLACK
VIOLET
VIOLET/BLACK
B.T. ANT ENNA
SPECIFICATION
General
Power Supply Requirements:
DC 14
.
4V“ ”, Negative Ground
Maximum Output Power:
Chassis Dimensions:
178 x 163x 50mm (W x D x H)
Tone Controls
Bass (at 100Hz):
+10dB / -10dB
Treble (at 10K):
+10dB / -10dB
Current Drain:
10A
CD Player
Signal to Noise Ratio:
More than 60dB
Channel Separation:
More than 60dB
Frequency Response:
20Hz - 20KHz
FM Radio
Frequency Coverage (MHz):
87
.
5 - 108MHz
IF :
10.7MHz
Sensitivity (S/N-30dB):
12dBu
Stereo Separation:
>30dB
75
W x
4
(
CH
)
Load
Impedance
:
4
ohms
Remarks
:
Specifications
subject
to
change
without
notice
RCD 120BT(/B) • MANUAL
RCD 120BT(/B) • MANUAL
Содержание RCD-120BT/B
Страница 1: ...RCD 120BT B MANUAL GB...
