CALEFFI iSolar Plus Скачать руководство пользователя страница 4

Страница: 4 / 52

us.ind

display

push button

fuse 4A

cable conduits with strain
relief

cover

1.1 Mounting

The unit must only be installed

• in a dry interior location

• in a non-hazardous location

• away from electromagnetic fields

The controller must additionally be supplied from a double-
pole switch with contact gap of at least 0.12" [3 mm].
Route sensor cables and power supply cables separately.

Unscrew the cross-head screw from the cover and
remove it along with the cover from the housing

Mark the upper fastening point on the wall and drill

Fasten the enclosed wall plug and screw leaving the
head protruding

Hang the housing from the upper fastening point and
mark the lower fastening point through the hole in the
terminal box (centers 5.1" [130 mm])

Drill and insert the lower wall plug

Fasten the housing to the wall with lower fastening
screw and tighten

Complete wiring connections in accordance with termi-
nal allocations, see chap. 1.2 “Electrical connection”

Place the cover back onto the housing

Fasten the cover by means of the cross-head screw

1. Installation

VBus

T4A

VBus

9 10

CU 72091163 01

1 (1) A (
1

100 ... 240) V~

(1) A (100 ... 240) V~

R1
R2

100 ... 240 V~

50-60 Hz

Temp. Sensor Pt1000

IP 20

DE-45527 Hattingen

DeltaSol BS Plus V2
Made in Germany

1.2 Electrical connection

power supply terminals

fuse

load terminals

sensor terminal

ground terminal

Note:

The minimum pump speed must be set to 100 %
when auxiliary relays or valves are connected.

WARNING! Electric shock!

Opening the housing will expose
live parts!

Switch off power supply and discon-
nect the device from power supply
before opening the housing!

ATTENTION! ESD damage!

Electrostatic discharge can lead to da-
mage to electronic components!

Take care to discharge properly
before touching the inside of the
device. To do so, touch a grounded
surface such as a radiator or tap!

104 mm

4.1“

130 mm

5.1“

upper fastening

lower fastening

Содержание iSolar Plus





















































Результаты поиска

Содержание iSolar Plus

Отзывы:

Похожие инструкции для iSolar Plus

Бренды по названию

Популярные бренды

CALEFFI iSolar Plus, Руководство пользователя

Результаты поиска

Содержание iSolar Plus

Отзывы:

Похожие инструкции для iSolar Plus

Бренды по названию

Популярные бренды