CalAmp LandCell SMC-GPRS Series Скачать руководство пользователя | Manualshive

Страница: 36 / 84

background image

001-0004-829 Rev00

Page 36 of 84

3 - CONNECT <text> result code returned, dial tone detection is disabled, busy
detection is enabled.
4 - CONNECT <text> result code returned, dial tone and busy detection are both
enabled.

AT\V

Set CONNECT result code format:
0 - CONNECT <text> result code returned without RLP trailer.
1 - CONNECT <text> result code returned with RLP trailer.

ATZ

Sets all current parameters to the user profile stored with

AT&W

. If a

connection is in progress, it will be terminated.

AT+CFUN

Sets phone functionality:

AT+CFUN=0

NON-CYCLIC SLEEP mode

AT+CFUN=1

Full functionality

AT+CFUN=7

CYCLIC SLEEP mode, In this mode, the serial interface is shortly

enabled while CTS is active. If characters are recognized on the serial interface,
the ME stays active for 2 seconds after the last character was sent or received.
ME exits SLEEP mode only, if AT+CFUN=1 is entered.

AT+CFUN=9

CYCLIC SLEEP mode, In this mode, the serial interface is shortly

enabled while CTS is active. If characters are recognized on the serial interface,
the ME stays active after the last character was sent or received for at least the
time, which can be configured by
AT^SCFG="PowerSaver/Mode9/Timeout",<psm9to> (temporary wakeup). In
contrast to SLEEP mode 7 assertion of RTS can also be used to temporarily wake
up the ME.

AT+CFUN=1,1

will re-start the SMC modem and clear volitile memory.

AT^SMSO

Initiates the power-off procedure.

AT+GCAP

Request complete TA capabilities list.

AT+CMEE

Mobile Equipment Error Message Format:

AT+CMEE=0

Disable result code, i.e. only "ERROR" will be displayed.

AT+CMEE=1

Enable error result code with numeric values.

AT+CMEE=2

Enable error result code with verbose (string) values.

AT+CSCS

Select TE character set:

AT+CSCS=“GSM“

GSM default alphabet (GSM 03.38 subclause 6.2.1); Note:

This setting may cause software flow control problems since the codes used to
stop and resume data flow (XOFF = decimal 19, XON = decimal 17) are
interpreted as normal characters.

AT+CSCS=“UCS2“

16-bit universal multiple-octet coded character set

(ISO/IEC10646 [32]); UCS2 character strings are converted to hexadecimal
numbers from 0000 to FFFF; e.g. "004100620063" equals three 16-bit
characters with decimal values 65, 98 and 99, $(AT R97)$

AT^SCFG

Extended Configuration Settings:
The

AT^SCFG?

read command returns a list of all supported parameters and

their current values.
The

AT^SCFG=

write command queries a configuration parameter (if no value

is entered) or sets its value(s). Input of parameter names is always coded in
GSM character set, parameter values are expected to be given as specified via
AT+CSCS.

AT^SM20

Sets M20 compatibility mode:

AT^SM20=

<CallMode>, <CmgwMode>

0 - Set compatibility to Siemens mobile phones.
1 - Default mode

«
...
34
35
36
37
38
...
»

Содержание LandCell SMC-GPRS Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для LandCell SMC-GPRS Series

Бренд: ADC Страницы: 7

Бренд: Hayes Microcomputer Products Страницы: 35

Бренд: Sierra Wireless Страницы: 13

Бренд: Multitech Страницы: 49

MA02-AAC 2220 Series

Бренд: Ebyte Страницы: 41

Бренд: GDI Страницы: 23

Бренд: Ovation Страницы: 9

PlantLinc PLR5000

Бренд: Data-Linc Group Страницы: 31

Бренд: Swann Страницы: 2

Бренд: Terayon Страницы: 24

Бренд: FAAC Страницы: 20

Skywire NL-LTE-TNAG

Бренд: NimbeLink Страницы: 8

Thomson TG797n V2

Бренд: Telecom Страницы: 10

Бренд: Swegon Страницы: 4

Mobile Broadband USB Modem

Бренд: Kajeet Страницы: 46

Бренд: Raymar Страницы: 23

Бренд: Hughes Страницы: 66

Бренд: Hughes Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды