CalAmp LandCell SMC-GPRS Series Скачать руководство пользователя | Manualshive

Страница: 49 / 84

background image

001-0004-829 Rev00

Page 49 of 84

ATD

Request GPRS or GPRS IP service:
This command causes the MT to perform whatever actions are necessary to
establish a communication between the TE and the external PDN.

Request GPRS service:

ATD*99**

<L2P>

*

<cid>

#

L2P:

blank – non PPP
“PPP“ - layer 2 protocol PPP
“1“ - layer 2 protocol PPP

cid:

1 – typically, set by AT+CGDCONT command.

Request GPRS IP service:

ATD*98*

<cid>

#

cid:

1 – typically, CID defined by AT+CGDCONT command.

ATH

Manual rejection of a network request for PDP context activation:
The command may be used to deactivate all PDP contexts which are active or
online on the same interface.

ATS0

Automatic response to a network request for PDP context activation:
The Automatic answer command may be used to turn off (n=0) and on (n>0)
the automatic response to a network request for a PDP context activation.
=000 Disables automatic answer mode.
=001-255 Enables automatic answering after specified number of rings.

Short Message Service (SMS) Commands

The AT Commands described in this section allow an external application to use the Short Message
Service with the modem.

A brief description of the GPRS commands are provided in Table 10.12. For futher information, refer
to the Cinterion TC63i AT Command Set document available from Cinterion

[2]

.

Table 10.12: SMS Command Reference

Command

Description

AT+CMGC

Send an SMS command

AT+CMGD

Delete SMS message

AT+CMGF

Select SMS message format

AT+CMGL

List SMS messages from preferred store

AT+CMGR

Read SMS messages

AT+CMGS

Send SMS message

AT+CMGW

Write SMS messages to memory

AT+CMSS

Send SMS messages from storage

AT+CNMA

New SMS message acknowledge to ME/TE, only phase 2+

AT+CNMI

New SMS message indications

AT+CPMS

Preferred SMS message storage

AT+CSCA

SMS service centre address

AT+CSCB

Select Cell Broadcast Message Indication

AT+CSDH

Show SMS text mode parameters

AT+CSMP

Set SMS text mode parameters

AT+CSMS

Select Message Service

AT^SCML

List Concatenated SMS messages from preferred store

«
...
47
48
49
50
51
...
»

Содержание LandCell SMC-GPRS Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для LandCell SMC-GPRS Series

Бренд: Data-Linc Group Страницы: 4

Бренд: PROLiNK Страницы: 19

Бренд: US Robotics Страницы: 129

Бренд: Radyne Страницы: 11

Бренд: Draytek Страницы: 288

Бренд: T-Home Страницы: 168

Бренд: AirLive Страницы: 77

Бренд: Infiniteq Страницы: 11

Бренд: Honeywell Страницы: 87

Бренд: Huawei Страницы: 9

Бренд: Zte Страницы: 40

BritePort 8012-G1

Бренд: Broadxent Страницы: 55

COR IBR1100 series

Бренд: Cradlepoint Страницы: 5

Бренд: Cradlepoint Страницы: 20

HomeConnect 3CR29221

Бренд: 3Com Страницы: 1

DG834Gv3 - 54 Mbps Wireless ADSL Firewall Modem

Бренд: NETGEAR Страницы: 32

Бренд: Hughes Страницы: 17

Бренд: D-Link Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды