CalAmp LandCell SMC-GPRS Series Скачать руководство пользователя | Manualshive

Страница: 26 / 84

background image

001-0004-829 Rev00

Page 26 of 84

Define the GPRS Context

Exact settings of GPRS context and Quality of Service Profiles are provisioned by the network
provider and must be requested before defining the GPRS context. Every PDP context has a
context identifier <cid>. The context identifiers are numbered sequentially and have to start with
value 1.

AT+CGDCONT

is used to define a context ID and specify the PDP type and Access Point Name

(APN). The PDP type describes the protocol to be used between the ME and the network. The
APN specifies the gateway between mobile network and the internet.

GPRS PDP Context activation/ deactivation

The

AT+CGACT=<state>,<cid>

command activates (state=1) and deactivates (state=0) a

specified PDP Context. If a PDP Context is already in the requested state, the state of this
context remains unchanged.

If the ME is not yet attached to the GPRS service, the attach will be done before the context
activation is executed. If no <cid> is specified (e.g. AT+CGACT=1 or AT+CGACT=0), all defined
contexts become activated/deactivated.

In many networks AT+CGACT=1 does not work any longer. Many networks require user name
and password for context activation. However these parameters are only handed to module
during the PPP traffic and not by AT command. Since the PPP traffic only starts when entering
the data mode, it is necessary to enter data mode before the actual PDP context activation
request is sent to the network. Use

ATD*99***<cid>#

to do so.

The command

AT+CGPADDR=<cid>

shows the PDP address, which was assigned to the

module during the activation process. The address may be static or dynamic.

GPRS Data Mode

Use the

ATD*99***<cid>#

command to go into GPRS data mode.

The PDP context (parameter <cid>) must be defined before via AT+CGDCONT.
If ATD*99***<cid># is entered without specifying a parameter, default parameters
will be used.

When entering the GPRS data mode, PPP traffic between the module and the application is
transferred. Therefore the application must be capable of handling PPP protocol.

Entering

+++

will switch from data mode or PPP online mode to command mode

Entering

ATO

or

AT+CGDATA

will switch from command mode to data mode

«
...
24
25
26
27
28
...
»

Содержание LandCell SMC-GPRS Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для LandCell SMC-GPRS Series

U.S. Robotics 56K Voice

Бренд: 3Com Страницы: 210

3C892 - OfficeConnect ISDN Lan Modem Router

Бренд: 3Com Страницы: 14

U.S. Robotics 56K Voice

Бренд: 3Com Страницы: 168

Бренд: TP-Link Страницы: 90

Бренд: Multitech Страницы: 90

AC/DC-POWERED USB HUB 4x USB 2.0

Бренд: WATSON Страницы: 6

Photo Backup STICK

Бренд: Paraben Страницы: 39

Бренд: Eaton Страницы: 2

Бренд: Blink Страницы: 4

Бренд: NETGEAR Страницы: 2

Бренд: 2TEST Страницы: 24

Бренд: Zte Страницы: 9

DSL-100D - 8 Mbps DSL Modem

Бренд: D-Link Страницы: 44

Бренд: US Robotics Страницы: 152

MOD 9001C RS232

Бренд: Sky Microwave Страницы: 13

Бренд: Zoomtak Telephonics Страницы: 75

Xstream 1300 Series

Бренд: Tainet Страницы: 86

Бренд: Daktronics Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды