2
2
2. Safety information
• The hose and seal on the regulator must be checked for wear or damage before every use and
before connecting to the gas cylinder.
• Ensure the appliance is used away from flammable materials. Minimum safe distances are
1.2m above the appliance and 600mm to the rear and sides of the appliance.
• Do not use an appliance that is damaged, leaking, or which does not operate properly.
• Keep gas cylinders away from heat and flames. Do not place on a stove or any other hot
surface.
• Ensure that the assembled unit is stable and does not rock.
• Do not cover or change the primary air supply openings in the burners as this will affect the
performance of the product and may lead to an unstable flame.
• In the event of burn back, (where the flame burns back and ignites at the jet), immediately
turn off the gas supply by first closing the control valve on the gas cylinder and then the
appliance valve. After the flame is extinguished remove the regulator and check the condition
of its seal. Replace the seal if in doubt. Re-light the appliance as described in Section 3
below. Should the flame light back persistently return the product to your authorized CADAC
repair agent.
• If there is a leak on your appliance (smell of gas), immediately close the control knob on
the gas cylinder. If you wish to check for leaks on your appliance, do it outside. Do not try to
detect leaks using a flame; use soapy water.
• The correct way is to smear the joints with soapy water. If a bubble or bubbles form then there
is a gas leak. Immediately turn off the gas supply firstly by closing the control valve on the
gas container and then the appliance valve. Check that all the connections are properly fitted.
Re-check with soapy water. If a gas leak persists, return the product to your CADAC dealer for
inspection / repair.
• Do not modify the appliance or use it for anything which it has not been designed for.
• During use, part of the appliance will become hot, particularly the cooking areas and the hood.
Avoid touching hot parts with your bare hands. The use of oven gloves is recommended.
• Keep young children away from the appliance at all times.
• This appliance consumes oxygen and needs ventilation for optimum performance and for the
safety of those in close proximity.
• Do not move the appliance while in use.
• The parts sealed by the manufacturer or its agent must not be altered by the user.
NOTE
• Do not twist or pinch the hose. Ensure that it is kept away from the BBQ body so as to prevent
deterioration/damage to the hose caused by heat.
• Fit one end of the low pressure hose onto the regulator nozzle, and the other end onto the
Patio BBQ nozzle by pushing the ends on as firmly as possible. Clamp into position using a
hose clamp at both ends of the hose.
• Ensure that the connections are made securely and do not allow gas to leak.
• Check for gas leaks before using the appliance.
• For use with an approved hose and regulator connected to a refillable gas container not
exceeding 9kg and complying with local regulation in force.
• Do not obstruct the ventilation openings of the cabinet.
• Do not modify the appliance. Modifying the appliance may be dangerous.
• Warning: Since this barbecue has no restriction in the emission of unburned gas, this
barbecue must be installed and/or used OUTDOORS or in an AMPLY VENTILATED AREA.
Ensure this BBQ is installed in an AMPLY VENTILATED AREA, the area must have at least
25% of the surface(sum of the walls surface) area open.
• Do not move the appliance during use.
• Any modification of the appliance may be dangerous.
•
Warning:
An LP cylinder not connected for use, shall not be stored in the vicinity of this or any
other appliance.
3. Assembly Instructions
• Use this appliance only on a firm level surface.
• Before use ensure that the drip cup is in place.
• Make sure the gas cylinder is correctly fitted to the appliance.
• Ensure the cylinder control valve is in the open position.
• To light the appliance using the automatic igniter, push in and turn the control knob in an
anti-clockwise direction until spring resistance is felt. Hold the knob in this position for 3 – 5
seconds to allow the gas to flow and then turn the knob fully anti-clockwise to the HIGH
position. This will cause the automatic lighter to light the burner. Should the burner not ignite
the first time, turn the control knob to the OFF position and wait 5 minutes, repeat the process
until the burner ignites.
• Note! All burners are fitted with an automatic igniter.
• Cross lighting: To light the burners using cross lighting, light the left burner as described above.
• To light the remainder of the burners, simply turn their control knobs to the HIGH position while ensuring that the lighting sequence is
such that any burner to be lit up is directly adjacent to a burner which is already burning.
GB
Содержание Meridian 3
Страница 2: ......
