CAB RB.400, Руководство пользователя

Страница: 21 / 40

22
4) POSITIONING THE SPRING AND THE ACCESSORIES FOR USE
Depending on the length of the bar and on the type of accessories installed, before putting the spring under tension it is necessary to choose the correct
point in which to attach the spring to the lever.
The correct fastening point (“A”, “B” or “C” - Fig.2), must be chosen in table 1, depending on the length of the bar and on the type of accessories you
intend to install.
RB.400 - TAB. 1
Bar lenght (m)
Accessories for use
2,2 2,7 3,2 3,7 4,2
NA
C C C B A
RB400.P(1)
C C B B A
RB400.P(2)
C C B B A
VE.RAST C B B A
RB400.P(1) + VE.RAST
C B B A
RB400.P(1) + VE.AM
C B B A A
RB400.P(2) + VE.AM
C B B A
RB400.P(1) + VE.RAST + VE.AM
C B A
SC.RES C B B A
RB400.P (1) + SC.RES
C B A A
SC.RES + VE.AM
C B A A
RB400.P(1)+ SC.RES + VE.AM
C B A
RB.500 - TAB. 1
Bar lenght (m)
Accessories for use
3,7 4,2 4,7 5,2
NA
C C
RB400.P(1)
C B B
RB400.P(2)
C C B B
VE.RAST
C B B A
RB400.P(1) + VE.RAST
C B A A
RB400.P(1) + VE.AM
C C B B
RB400.P(2) + VE.AM
C B B A
RB400.P(1) + VE.RAST + VE.AM
B B A A
SC.RES
C B B A
RB400.P (1) + SC.RES
C B A A
SC.RES + VE.AM
B B A A
RB400.P(1)+ SC.RES + VE.AM
B B A A
VE.RAST + VE.AM
B B A A
Key
NA No accessories
RB400.P(1) Protection profile (only upper).
RB400.P(2) Protection profiles (upper and lower).
VE.RAST
Aluminium skirt.
VE.AM Mobile support for bar.
SC.RES Sensitive resistive edge (complying EN12878).
Attention:
The installation of the VE.RAST interferes with the use of the SC.RES and vice versa.
The installation of the RB400.L lights kit does not influence the balancing of the bar
5) INSTALLATION OF THE OPTIONAL FOUNDATION PLATE VE.PS (FIG.3)
After preparing the cable laying (mains power supply, accessories, etc.), place the foundation plate keeping to dimensions indicated.
Brackets to be cemented are supplied with the system (ref. A). The brackets must be fitted to the foundation plate by means of nuts (B) and corresponding washers C.
Check that the foundation plate is perfectly flat (ref. F), then fix the road barrier by means of nuts D and corresponding washers E.
Notes: the special shape of the slots on the bottom of the barrier cabinet, allow to adjust finely the position of the barrier.
It is suggested to leave 30 mm of threaded bar out from the foundation plate, a bigger length could generate an interference with the spring, a smaller
length does not ensure the proper fixing of the barrier.
6) FIXING THE BAR (FIG.4)
The bar is fixed to the plate using the support and the screws provided, as illustrated in Fig.4. We recommend installing any accessories for the bar
(protective profiles, lights, edge, skirt, etc.) before fixing it to the plate.
7) PREPARING THE BARRIER FOR RIGHT OR LEFT (FIG.5)
If the opening direction reversion is required, proceed as follows. If it is not necessary, go to the next section:
• Entirely unload the spring by loosening it and unhooking it from the “L” anchoring lever
• unlock the geared motor (see “Manual Operation”) insofar as to render the L hooking lever idle.