CAB MAESTRO 6 Скачать руководство пользователя

Страница: 21 / 22

8.5

Change of blade type

Fig. 22

Change the blade type

1. Loosen the screws (3) on the support arms of the

blade carriage (4 or 1) on the back side of the
MAESTRO 6..

2. Remove blade carriage with mounted support

arms (4 or 1).

3. Hold the blade carriage (1 or 4) to the transport

system (2) of the MAESTRO 6 and secure it with
the screws (3).

8.6

Alignment of the blade carriage

4
5

Fig. 23

Alignment of the blade carriage

Remove the dial gauge (3) from the accessory pack of the MAESTRO 6 and fit it to the straight arm.

Now screw arm with built-on dial gauge (3) to the side of the carriage profile.

6. The dipstick of the dial gauge (3) must be pressed in slightly. about 5mm

7. Push the blade carriage up to the dial gauge and determine the difference between the linear blade (1) and the

circular blades (2).

8. With the help of the eccentrics (4) and the screws (5) with corresponding oblong holes on both sides of the carrier,

the blade carriage can be aligned with the linear blade (1).

Replacement of the Blades

Содержание MAESTRO 6























Результаты поиска

Содержание MAESTRO 6

Отзывы:

Похожие инструкции для MAESTRO 6

Бренды по названию

Популярные бренды

CAB MAESTRO 6, Руководство оператора

Результаты поиска

Содержание MAESTRO 6

Отзывы:

Похожие инструкции для MAESTRO 6

Бренды по названию

Популярные бренды