C-TEC EACIE Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 38

C-TEC EACIE Скачать руководство пользователя страница 23

EACIE Evacuation Alert Control and Indicating Equipment

Page 23 of 38



Approved Document No. DFU5030020 Rev 1



Installation and Programming Manual

7.4

Engineering Functions

The Engineering Functions menu is used to access the panel’s comprehensive test functions and display
important system status information.

At Access Level 3, press the

button and the window shown below left appears.

Scroll down

to view additional engineering menu options (shown below right).

Engineering functions are listed in sections 7.4.1 to 7.4.9.

7.4.1

Device Manager

Using this function you can display, edit and test all the addressable devices stored in the panel’s memory
which include loop devices and system devices.

At Access Level 3 > Engineering Functions, press the

button and a window similar to

the one shown below appears.

Loop 1 is shown selected as an example.

To view all the devices on the loop, use the

and

buttons to scroll through all the devices.

Loop 1 shown selected

Loop Devices window:

- displays loop addresses (up to 66 devices per loop)

- displays loop device icons, examples shown below:

- CAST CA736/CA737 Sounder Controller

- denotes ‘no device fitted’

«
...
21
22
23
24
25
...
»

Содержание EACIE







































Отзывы:

Нет отзывов