C-TEC EACIE Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 38

C-TEC EACIE Скачать руководство пользователя страница 13

EACIE Evacuation Alert Control and Indicating Equipment

Page 13 of 38



Approved Document No. DFU5030020 Rev 1



Installation and Programming Manual

5.5

Inserting the ‘slide-in’ labels

A customisable ‘slide-in’ label system is employed by the EACIE panel for both the Z41/CA module (for use by
an authorised engineer) and the 8 way switch panels (for use by the FRS).

Label templates for customising are available

on C-TEC’s website

Z41/CA Control/Display Module Label

The slide-in labels for the programmable LEDs depends on how the unit has been
configured. Insert the labels (supplied in the accessory pack) for the Z41/CA, as
shown right.

Important Note:

Before inserting the horizontal ‘Fire/Fault/Disablement/Test’

label in the Z41/CA module, create a ‘slight’

bend (NOT A FOLD!) at the left-hand side of the label (approx. 20mm). Gently push the label through the slot
provided into its housing using the hinge on the module’s rack to assist with finding its path, as shown below.

Switch/Indicator Module Label

Dependent on programming, the slide-in label can be customised on a zone-
by-zone or floor-by-floor basis for each toggle switches.

Insert the slide-in labels (supplied in the accessory pack) for the switch
module(s), as shown right.

Note:

The maximum thickness of paper for the label is 80gsm or standard

photocopier paper.

«
...
11
12
13
14
15
...
»

Содержание EACIE







































Отзывы:

Нет отзывов