C. B. Gitty Crafter Supply Cigar Box Ukulele Kit Скачать руководство пользователя страница 8

Страница: 8 / 14

y Cra

er Supply 8

lid, center the bridge at the appropriate distance from the top of the fret board. Making certain that it is cen-

tered will properly align the bridge and saddle with the fret board.

Through the holes you’ve drilled, mark the box lid. Use a

⅛

” bit to drill holes through the lid and into the brace

at the points you’ve marked, as shown in

Figure 20

If you are going to treat the bridge with any finishes, doing so now before it gets fastened to the box is a good

idea. Smoothing off the sharper edges

and points is also a good idea at this

point—you don’t want anything that will

dig into your strumming arm when play-

ing.

Step 3—Prepare and Install
the Saddle

This is also a good time to smooth and

round the ends of the bone saddle, espe-

cially the end that will be towards the top

of the instrument when it is held for play-

ing, for the same reason as above—a

sharp edge on the bone saddle can dig

into your strumming arm, and no musi-

cian likes that!

Carefully insert the bone saddle into the

bridge. Do not force it in. If need be, re-

move a tiny amount of material from the

slot for the saddle with a razor knife or

file. You want the saddle to fit snugly

Figure 14

Figure 15

Содержание Cigar Box Ukulele Kit














Результаты поиска

Содержание Cigar Box Ukulele Kit

Отзывы:

Похожие инструкции для Cigar Box Ukulele Kit

Бренды по названию

Популярные бренды

C. B. Gitty Crafter Supply Cigar Box Ukulele Kit, Руководство по сборке

Результаты поиска

Содержание Cigar Box Ukulele Kit

Отзывы:

Похожие инструкции для Cigar Box Ukulele Kit

Бренды по названию

Популярные бренды