C. B. Gitty Crafter Supply Cigar Box Ukulele Kit Скачать руководство пользователя страница 10

Страница: 10 / 14

y Cra

er Supply 10

After removing the clamps from

gluing the fretboard to the neck,

apply a small amount of wood

glue to the nut. Clamp it in place,

as shown in

Figure 24

, with the

flat edges butted up against the

top edge of the fret board and the

neck, as shown in the photo. Be

sure to wipe off any excess glue

with a cloth.

Once dried and the clamp re-

moved, any final sanding and

treatment of the neck can be done

(if desired).

Now it is time to install the tuners

into the headstock of the instru-

ment.

Figure 25

shows a tuner

laid out (with its parts in the order

of assembly, as well as an assem-

bled tuner.

Install your tuners as shown in

Figure 26 and 27

with the bev-

eled and locking washers on the

back of the headstock and the

plastic washer and bushing on the

front. The tuning shaft will join all

the components with the tuner

button screwed into the end.

At this point, make certain to tight-

en the screws attaching each

white plastic button to the corre-

sponding tuner shaft. Tight screws

will help to prevent the pegs from

unwinding under the tension of

being strung up.

Step 2—Cut Sound
holes (Optional)

If you haven’t cut or drilled any

sound holes into the lid, now

would be a good time to do so

before you get too much further.

Sound holes are largely a matter

of personal preference as to

where, what, and how big. Just be

mindful of what you may visually

expose inside the box.

You can always search sites like

CigarBoxNation.com

for any ideas

and examples. The box we used

in this guide had “F-hole”-style

sound holes cut into it before we

started, but a single round hole in

the center of the box, sized be-

tween 3/4 and 1 1/2 inches, also

Figure 18

Figure 19

Figure 20

Содержание Cigar Box Ukulele Kit














Результаты поиска

Содержание Cigar Box Ukulele Kit

Отзывы:

Похожие инструкции для Cigar Box Ukulele Kit

Бренды по названию

Популярные бренды

C. B. Gitty Crafter Supply Cigar Box Ukulele Kit, Руководство по сборке

Результаты поиска

Содержание Cigar Box Ukulele Kit

Отзывы:

Похожие инструкции для Cigar Box Ukulele Kit

Бренды по названию

Популярные бренды