C. B. Gitty Crafter Supply Cigar Box Ukulele Kit Скачать руководство пользователя страница 4

Страница: 4 / 14

y Cra

er Supply 4

Step 3—Drilling the Neck Mounting Holes in the Neck

Now, line the neck back up to the box, in position where it will be mounted, and make a mark through each

the holes you just drilled onto the flat part of the neck heel. The scratch awl or a small nail is very handy for

this. The result of the first mark is shown in

Figure 6

With all three holes marked on the neck heel, once again use the 1/8” drill but to pre-drill the heel for the

mounting screws. Be very careful at this point not to drill too deep - wrapping some painter’s tape around the

drill bit as a visual depth stop is a good idea.

Keep in mind that the two longer 2” neck mounting screws will go into the upper two holes, and the shorter 1

5/8” screw will go into the lower hole.

It can make things easier if you drill the first mounting

hole into the neck, and then insert a single screw to hold

the neck in place, and then mark the other two holes.

This will keep the neck from moving/shifting, and it is

very important that all of these holes line up properly—

you don’t want your neck to be crooked.

Now mark and drill the two remaining holes. When fin-

ished, your box and neck should be fully drilled with the

three neck-mounting holes. Do a “dry fit” of the neck to

make sure everything looks good.

This is a good time to remove the painter’s tape (if you

used any) from the box surface.

Figure 8

shows what

the neck should look like when all 3 holes have been

drilled.

You can now test-mount your neck to the box using the 3

neck mounting screws. Remember that the two longer

ones go on top, the shorter one on bottom. Make sure

everything is lined up and looking good. A “stubby” Phil-

lips screwdriver is best for this.

Remember that you want the neck’s flat upper surface to

be as parallel as possible with the surface of the box.

Figure 3

Figure 5

Figure 4

Содержание Cigar Box Ukulele Kit














Результаты поиска

Содержание Cigar Box Ukulele Kit

Отзывы:

Похожие инструкции для Cigar Box Ukulele Kit

Бренды по названию

Популярные бренды

C. B. Gitty Crafter Supply Cigar Box Ukulele Kit, Руководство по сборке

Результаты поиска

Содержание Cigar Box Ukulele Kit

Отзывы:

Похожие инструкции для Cigar Box Ukulele Kit

Бренды по названию

Популярные бренды