background image

B.Y.O.C. Large Beaver Parts Checklist

Resistors:
2 x 100ohm (brown/black/black/black/brown)

1 x 120ohm (brown/red/black/black/brown) don't confuse this one with the 10K!!!!!
2 x 150ohm (brown/green/black/black/brown)

2 x 820ohm (gray/red/black/black/brown)

NOT INCLUDED IN KITS PURCHASED

AFTER 6/1/08

1 x 1k (brown/black/black/brown/brown)

1 x 2.7k (red/purple/black/brown/brown)

1 x 3.3k (orange/orange/ black/brown/brown)

1 x 4.7k (yellow/purple/black/brown/brown)

2 x 8.2k (gray/red/black/brown/brown)

4 x 10k (brown/black/black/red/brown) don't confuse these with the 120ohm!!!!

2 x 12k (brown/red/black/red/brown)

2 x 15k (brown/green/black/red/brown)

2 x 22k (red/red/black/red/brown)
1 x 33k (orange/orange/black/red/brown)

2 x 39k (orange/white/black/red/brown)

1 x 47k (yellow/purple/black/red/brown)

3 x 82k (gray/red/black/red/brown)

3 x 100k (brown/black/black/orange/brown)

4 x 390k (orange/white/black/orange/brown)

1 x 430k (yellow/orange/black/orange/brown)

3 x 470k (yellow/purple/black/orange/brown)

1 x 1M (brown/black/black/yellow/brown)

Capacitors:

3 x 560pf ceramic disc (561 small orange)
2 x .0039uf (392 or 3n9)

2 x .01uf film (103 or 10n)

2 x .05 ceramic disc

 (OR .047 film caps 473 or 47n)

6 x 0.1uf film (104 or 100n)

3 x 1uf aluminum electrolytic

1 x 10uf aluminum electrolytic

transistors:

4 x 2N5133

NOT INCLUDED IN KITS PURCHASED AFTER 6/1/08

4 x BC239C

4 x transistor sockets

NOT INCLUDED IN KITS PURCHASED AFTER 6/1/08

Diodes:

4 x 1N4148 or 1N914

potentiometers:

(be sure to snap off the small post on the top side of the pot with a pair of

needle nose pliers)

Содержание Large Beaver PCB






























Отзывы: