BYD BYD5030XXYBEV2 Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 252

background image

236

8-1 When Failure Occurs



If the tyre pressure is in the range of
180~320kPa (yellow and green zones
shown in the figure), remove the kit as
soon as possible, and within 1 min, start
driving the vehicle at a speed lower than
80km/h for a distance not exceeding 10
km to allow the tyre puncture sealant to
be uniformly distributed in the tyre.

8. Stop the vehicle and observe the tyre
pressure.



If the tyre pressure is greater than
220kPa (green zone shown in the
figure), drive the vehicle at a speed
lower than 80km/h to a nearest service
provider.



If the tyre pressure is in the range of
130~220kPa (yellow zone shown in the
figure), repeat steps 6 and 7.



If the tyre pressure does not reach 130
kPa (red zone shown in the figure),
contact a BYD authorised service
provider.

WARM TIP



Repairing a damaged tyre with tyre puncture sealant is an emergency solution only.
Please replace the tyre in a professional maintenance center as soon as possible (it is
recommended that you contact a BYD authorised service provider) and tell a
professional technician that the tyre has tyre puncture sealant inside.



Avoid quick acceleration or turning at a high speed.



Follow the limit requirement of maximum vehicle speed of 80km/h.



After repairing a tyre with the tyre puncture sealant kit, it is recommended that you
purchase a new tyre puncture sealant and inflator hose from a BYD authorised service
provider.

«
...
234
235
236
237
238
...
»

Содержание BYD5030XXYBEV2





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BYD5030XXYBEV2

Бренд: Lancia Страницы: 191

Бренд: Rola Страницы: 3

Бренд: Phonocar Страницы: 2

Car Cup Holder Phone Mount

Бренд: UGREEN Страницы: 9

Code Alarm PROFESSIONAL SERIES CA 5550SST

Бренд: Audiovox Страницы: 14

Road Ready Seat Protector

Бренд: Wagan Страницы: 12

Бренд: Chevrolet Страницы: 50

Бренд: SAN HIMA Страницы: 10

Бренд: Ford Страницы: 458

Бренд: Yakima Страницы: 12

Бренд: Tesla Страницы: 274

Бренд: SSV Works Страницы: 2

transit connect 2012

Бренд: Ford Страницы: 299

Бренд: Car-Interface Страницы: 25

Бренд: Ultraplast Страницы: 5

Бренд: MBW Страницы: 40

Quad Gear 18-029-010401-00-SC

Бренд: Classic Accessories Страницы: 4

ESCALADE EXT - DATASHEET 2011

Бренд: Cadillac Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды