BWT 3 x 3 Скачать руководство пользователя

Страница: 41 / 48

41/48

2019/01 - Indice de révision : A - Code : 97160421

WOODEN POOLS

BWT

myPOOL

HOTLINE

20.1

Winterizing the pool

NOTE: Winterizing is not mandatory, particularly in clement climates where temperatures remain

positive year round.

In this case, keep the water at the correct level and run the filter for 2 to 3 hours per day. Check the

water level in the pool regularly.

•

Carry out a prolonged back wash of the filter.

•

The pool should not be emptied during winter (or prolonged periods while the pool is not use). The

liquid mass plays a several roles, providing thermal insulation, holding the liner and pool structure

in position.

•

Lower the water level to about 10 cm below the bottom of the skimmer mouth.

•

Water can be siphoned from the pool or allowed to drain by gravity by moving the multi-port valve to

DRAIN. Water will run through the waste line. Do not run the pump during this operation.

•

Next, disconnect the pipe underneath the skimmer so that it can act as an overflow in the event

the water level rises due to precipitation. Remove any water treatment chemicals from the skimmer

(chlorine tablets, flocculants, etc.).

•

Unscrew the return fitting face ring from inside the pool.

•

Use a threaded winterizing plug or rubber plug (not provided) to block the return fitting from inside

the pool.

•

Add an algicide and a winterizing product (not supplied) to the water.

•

Remove the stainless steel ladder.

•

Place a winter cover over the surface of the pool (If the pool is fitted with one).

20.1.1 Winterizing the hydraulic installation

•

Disconnect the return line.

•

Allow water to drain from the suction and return lines.

•

Open the plug at the bottom of the filter and allow water to drain away. Do not replace the plug until

the filter is being put back into service.

•

Open the drain plugs on the pump and pre-filter.

•

Leave the plugs open.

•

Cut the power supply to the filtration control panel.

•

In as far as possible, store the filtration group in a location protected from humidity. In the case of an

unprotected outdoor installation, remove the pump and store it.

•

We think that we have provided you with main information you require to use and maintain your pool,

however you will find more information in specialised guides and reviews. Don’t hesitate to consult

these.

20.2

Water treatment

To ensure correct usage of your pool, make sure that the water is treated properly. To do this, follow the

recommendations pertaining to usage of your filtration group: commissioning, bather load in the context

of water regeneration, maintenance and inspection of this system (pipes, bolts, screws). Monitor the

build up of impurities in the sand filter (refer to the filter backwash procedure).
Similarly, it is important to check that the filtration ports are not blocked

•

Filtration should be stopped during interventions on the filtration system.

•

Do not allow access to the pool if the filtration system is not running properly.

•

Damaged elements or assemblies must be replaced as quickly as possible.

•

Only use parts approved by our after sales service.

During the pool season, the filter should be run every day for long enough to allow the entire pool water

volume to pass through the filter at least three times every 24 hours.

Содержание 3 x 3

















































Результаты поиска

Содержание 3 x 3

Отзывы:

Похожие инструкции для 3 x 3

Бренды по названию

Популярные бренды

BWT 3 x 3, Инструкции по установке и эксплуатации

Результаты поиска

Содержание 3 x 3

Отзывы:

Похожие инструкции для 3 x 3

Бренды по названию

Популярные бренды