BWT 3 x 3 Скачать руководство пользователя страница 33

Страница: 33 / 48

33/48

2019/01 - Indice de révision : A - Code : 97160421

WOODEN POOLS

BWT

myPOOL

HOTLINE

16.6

Filling the water circuit

If the pool is to installed in-ground, check for leaks before burying the lines and connections

Open the various valves to fill the hydraulic circuit with water. Check for leaks at the connections.
Before starting the pump (the pump should never be allowed to run ‘dry’) check that the pre-filter has

filled with water. If necessary, open the pre-filter and fill it and the skimmer with water to facilitate priming

of the pump.

Turn the 6-way valve to Back Wash (to clean the filter before starting filtration).

16.7

Filling the pool and cutting the liner

If while filling the pool you note that the liner has been pulled out of the track, stop filling before

reengaging it. You may have to partially empty the pool before you will be able to rehang the liner.

Repositioning of the liner by sliding it along the track is prohibited, this could cause the liner to tear.

Release the liner then reposition it.

Refer to the additional installation instructions provided with the various fittings.

Once the creases on the floor of the pool have been eliminated, continue filling until the water level is

5 cm below the first pool fittings (return fittings). At this point, mark the position of the holes in the pool

fittings through the liner and mount the various flanges. Don’t forget to apply the second gasket to each

flange before screwing it into position.

Figure 48 – Mark the location of the holes

Figure 49 –

Apply the gasket to the flange

Figure 50 –

Mount the flange

Mark the holes for the screws. Apply the second flange. Screw into position (pozi countersunk head

screws TFZ M5x16 from the Pool Fitting skin). Tighten screws alternately and moderately by hand.
Proceed in the same way to fit the skimmer flanges.

Figure 51 –

Apply the gasket to the flange

Figure 52 –

Mount the second flange

Next, using a Stanley knife, cut the liner inside the flanges.

Содержание 3 x 3

















































Результаты поиска

Содержание 3 x 3

Отзывы:

Бренды по названию

Популярные бренды

BWT 3 x 3, Инструкции по установке и эксплуатации

Результаты поиска

Содержание 3 x 3

Отзывы:

Бренды по названию

Популярные бренды