![background image](http://html.mh-extra.com/html/bushranger/cs4020/cs4020_operators-manual_2835578011.webp)
11
STARTING THE COLD ENGINE
• Fill the fuel tank with 2 stroke fuel.
• Fill the chain oil tank with bar and chain
lubricant.
• Press hand guard forward. (Chain brake
ACTIVATED position).
• Turn ignition switch upside.
• Pull choke control knob all the way out.
• Securely hold the chain saw.
• Make sure guide bar and saw chain are not
touching anything when starting the saw.
•
Pull starter handle several times until first
firing sound is heard.
• Push choke control knob all the way in.
• Pull starter handle again.
WARNING DANGER
• After choke control knob is pulled and then
knob is returned to original position, throttle
remains a little open (latch condition).
• If engine is started in this latch condition,
chain starts to turn. DO NOT start engine
before chain brake is activated.
NOTE
Do not pull starter rope out to the maximum
position. Do not allow starter handle to snap
back against the casing.
CAUTION
• After starting the engine, squeeze trigger
slightly to release throttle latch and pull
front hand guard towards the operator
immediately. (Chain brake RELEASED
position).
• Do not increase engine speed while chain
brake is engaged.
• Use the chain brake in an emergency. Do not
use it unless absolutely necessary.
CAUTION
When throttle latch is used, saw chain will go
into motion as soon as the engine starts. Never
use throttle latch for cutting. Use it only when
starting the engine.
STARTING WITH WARM ENGINE
•
Confirm fuel and chain oil in the tanks.
• Press hand guard forward. (Chain brake
ACTIVATED position).
• Turn ignition switch up side.
• Securely hold the chain saw.
• Pull starter handle.
• Choke may be used if necessary but after
first firing sound, pull throttle trigger a little to
release throttle latch and choke.
CAUTION
Clutch engages and chain and will rotate when
engine is started with throttle trigger squeezed.
After engine starts release throttle trigger to idle
position.
STARTING THE COLD ENGINE
STARTING THE WARM ENGINE
RUNNING
•Fill the fuel tank with fuel.
•Fill the chain oil tank with lubricant.
•Press hand guard forward. (Chain brake ACTIVATED
position)
•Turn ignition switch upside.
•Pull choke control knob all the way out.
WARNING ▲ DANGER
•AFTER CHOKE CONTROL KNOB IS PULLED AND
THEN KNOB IS RETURNED TO ORIGINAL
POSITION, THROTTLE REMAINS A LITTLE OPEN
(LATCH CONDITION).
•IF ENGINE IS STARTED IN THIS LATCH
CONDITION, CHAIN STARTS TO TURN. DO NOT
START ENGINE BEFORE CHAIN BRAKE IS
ACTIVATED.
NOTE
Do not pull starter rope out to the maximum position.
Do not allow starter handle to snap back against the
casing.
CAUTION
1. After starting the engine, squeeze trigger
slightly to release throttle latch and pull front
hand guard towards the operator immediately.
(Chain brake RELEASED position)
2. Do not increase engine speed while chain brake is
engaged.
3. Use the chain brake in an emergency.
Do not use it unless absolutely necessary.
CAUTION
When throttle latch is used, saw chain will go into
motion as soon as the engine starts.
Never use throttle latch for cutting.
Use it only when starting the engine.
•Securely hold the chain saw.
•Make sure guide bar and saw chain are not touching
anything when starting the saw.
•Pull starter handle several times until first firing sound
is heard.
•Push choke control knob all the way in.
•Pull starter handle again.
•Confirm fuel and chain oil in the tanks.
•Press hand guard forward. (Chain brake ACTIVATED
position)
•Turn ignition switch up side.
•Securely hold the chain saw.
•Pull starter handle.
•Choke may be used if necessary but after first firing
sound, pull throttle trigger a little to release throttle
latch and choke.
CAUTION
Clutch engages and chain will rotate when engine is
started with throttle trigger squeezed. After engine
starts release throttle trigger to idle position.
•After engine starts, allow it to idle for a few minutes.
•Squeeze throttle trigger gradually to increase engine
revolution.
•The chain starts moving when the engine reaches
3,800 r/min approximately.
•Ensure proper acceleration and lubrication of saw
chain and guide bar.
•Do not run the engine at high speed unnecessarily.
•Be sure that saw chain stops moving when throttle
trigger is released.
STARTING THE COLD ENGINE
STARTING THE WARM ENGINE
RUNNING
•Fill the fuel tank with fuel.
•Fill the chain oil tank with lubricant.
•Press hand guard forward. (Chain brake ACTIVATED
position)
•Turn ignition switch upside.
•Pull choke control knob all the way out.
WARNING ▲ DANGER
•AFTER CHOKE CONTROL KNOB IS PULLED AND
THEN KNOB IS RETURNED TO ORIGINAL
POSITION, THROTTLE REMAINS A LITTLE OPEN
(LATCH CONDITION).
•IF ENGINE IS STARTED IN THIS LATCH
CONDITION, CHAIN STARTS TO TURN. DO NOT
START ENGINE BEFORE CHAIN BRAKE IS
ACTIVATED.
NOTE
Do not pull starter rope out to the maximum position.
Do not allow starter handle to snap back against the
casing.
CAUTION
1. After starting the engine, squeeze trigger
slightly to release throttle latch and pull front
hand guard towards the operator immediately.
(Chain brake RELEASED position)
2. Do not increase engine speed while chain brake is
engaged.
3. Use the chain brake in an emergency.
Do not use it unless absolutely necessary.
CAUTION
When throttle latch is used, saw chain will go into
motion as soon as the engine starts.
Never use throttle latch for cutting.
Use it only when starting the engine.
•Securely hold the chain saw.
•Make sure guide bar and saw chain are not touching
anything when starting the saw.
•Pull starter handle several times until first firing sound
is heard.
•Push choke control knob all the way in.
•Pull starter handle again.
•Confirm fuel and chain oil in the tanks.
•Press hand guard forward. (Chain brake ACTIVATED
position)
•Turn ignition switch up side.
•Securely hold the chain saw.
•Pull starter handle.
•Choke may be used if necessary but after first firing
sound, pull throttle trigger a little to release throttle
latch and choke.
CAUTION
Clutch engages and chain will rotate when engine is
started with throttle trigger squeezed. After engine
starts release throttle trigger to idle position.
•After engine starts, allow it to idle for a few minutes.
•Squeeze throttle trigger gradually to increase engine
revolution.
•The chain starts moving when the engine reaches
3,800 r/min approximately.
•Ensure proper acceleration and lubrication of saw
chain and guide bar.
•Do not run the engine at high speed unnecessarily.
•Be sure that saw chain stops moving when throttle
trigger is released.
STARTING THE COLD ENGINE
STARTING THE WARM ENGINE
RUNNING
•Fill the fuel tank with fuel.
•Fill the chain oil tank with lubricant.
•Press hand guard forward. (Chain brake ACTIVATED
position)
•Turn ignition switch upside.
•Pull choke control knob all the way out.
WARNING ▲ DANGER
•AFTER CHOKE CONTROL KNOB IS PULLED AND
THEN KNOB IS RETURNED TO ORIGINAL
POSITION, THROTTLE REMAINS A LITTLE OPEN
(LATCH CONDITION).
•IF ENGINE IS STARTED IN THIS LATCH
CONDITION, CHAIN STARTS TO TURN. DO NOT
START ENGINE BEFORE CHAIN BRAKE IS
ACTIVATED.
NOTE
Do not pull starter rope out to the maximum position.
Do not allow starter handle to snap back against the
casing.
CAUTION
1. After starting the engine, squeeze trigger
slightly to release throttle latch and pull front
hand guard towards the operator immediately.
(Chain brake RELEASED position)
2. Do not increase engine speed while chain brake is
engaged.
3. Use the chain brake in an emergency.
Do not use it unless absolutely necessary.
CAUTION
When throttle latch is used, saw chain will go into
motion as soon as the engine starts.
Never use throttle latch for cutting.
Use it only when starting the engine.
•Securely hold the chain saw.
•Make sure guide bar and saw chain are not touching
anything when starting the saw.
•Pull starter handle several times until first firing sound
is heard.
•Push choke control knob all the way in.
•Pull starter handle again.
•Confirm fuel and chain oil in the tanks.
•Press hand guard forward. (Chain brake ACTIVATED
position)
•Turn ignition switch up side.
•Securely hold the chain saw.
•Pull starter handle.
•Choke may be used if necessary but after first firing
sound, pull throttle trigger a little to release throttle
latch and choke.
CAUTION
Clutch engages and chain will rotate when engine is
started with throttle trigger squeezed. After engine
starts release throttle trigger to idle position.
•After engine starts, allow it to idle for a few minutes.
•Squeeze throttle trigger gradually to increase engine
revolution.
•The chain starts moving when the engine reaches
3,800 r/min approximately.
•Ensure proper acceleration and lubrication of saw
chain and guide bar.
•Do not run the engine at high speed unnecessarily.
•Be sure that saw chain stops moving when throttle
trigger is released.
STARTING THE COLD ENGINE
STARTING THE WARM ENGINE
RUNNING
•Fill the fuel tank with fuel.
•Fill the chain oil tank with lubricant.
•Press hand guard forward. (Chain brake ACTIVATED
position)
•Turn ignition switch upside.
•Pull choke control knob all the way out.
WARNING ▲ DANGER
•AFTER CHOKE CONTROL KNOB IS PULLED AND
THEN KNOB IS RETURNED TO ORIGINAL
POSITION, THROTTLE REMAINS A LITTLE OPEN
(LATCH CONDITION).
•IF ENGINE IS STARTED IN THIS LATCH
CONDITION, CHAIN STARTS TO TURN. DO NOT
START ENGINE BEFORE CHAIN BRAKE IS
ACTIVATED.
NOTE
Do not pull starter rope out to the maximum position.
Do not allow starter handle to snap back against the
casing.
CAUTION
1. After starting the engine, squeeze trigger
slightly to release throttle latch and pull front
hand guard towards the operator immediately.
(Chain brake RELEASED position)
2. Do not increase engine speed while chain brake is
engaged.
3. Use the chain brake in an emergency.
Do not use it unless absolutely necessary.
CAUTION
When throttle latch is used, saw chain will go into
motion as soon as the engine starts.
Never use throttle latch for cutting.
Use it only when starting the engine.
•Securely hold the chain saw.
•Make sure guide bar and saw chain are not touching
anything when starting the saw.
•Pull starter handle several times until first firing sound
is heard.
•Push choke control knob all the way in.
•Pull starter handle again.
•Confirm fuel and chain oil in the tanks.
•Press hand guard forward. (Chain brake ACTIVATED
position)
•Turn ignition switch up side.
•Securely hold the chain saw.
•Pull starter handle.
•Choke may be used if necessary but after first firing
sound, pull throttle trigger a little to release throttle
latch and choke.
CAUTION
Clutch engages and chain will rotate when engine is
started with throttle trigger squeezed. After engine
starts release throttle trigger to idle position.
•After engine starts, allow it to idle for a few minutes.
•Squeeze throttle trigger gradually to increase engine
revolution.
•The chain starts moving when the engine reaches
3,800 r/min approximately.
•Ensure proper acceleration and lubrication of saw
chain and guide bar.
•Do not run the engine at high speed unnecessarily.
•Be sure that saw chain stops moving when throttle
trigger is released.
Throttle trigger
Throttle trigger lockout
Starter handle
Содержание CS4020
Страница 1: ...1 CHAINSAW CS4020 OPERATOR S MANUAL ...
Страница 23: ...23 NOTES ...