15
CAUTION
Do not saw above chest height.
BUCKING
Bucking is the sawing of a log or fallen tree into smaller pieces. There are a few basic rules which apply to all bucking
operations. Keep both hands on the handles at all times. Support logs if possible. When cutting on a slope or hillside, always
stand uphill.
FELLING A TREE (continued)
Start the back cut on one side of the tree with spiked bumper engaged, pivoting the saw through to from the desired
hinge on that side. Then remove the saw for the second cut. Insert the saw in the first cut very carefully so as not to cause
kickback. The final cut is made by drawing the saw forward in the cut to reach the hinge. (See figure D).
14
GENERAL CUTTING INSTRUCTIONS
(CONTINUED)
Start the engine, see that is running properly.
Squeeze the trigger to open the throttle wide
open, then start the cut. It is not necessary to
press down hard to make the saw cut. If the
chain is properly sharpened, the cutting
should be relatively effortless. Pushing the saw
too hard will slow the engine and cutting will
actually be more difficult.
Some material may adversely affect the housing
of your chain saw.
(Example: palm tree acid, fertilizer etc.)
To avoid housing deterioration carefully remove
all packed saw dust around clutch and guide bar
area and wash with water.
WARNING DANGER
Do not let the nose or tip of the guide bar touch
anything while the engine is running to avoid
kickback.
FELLING A TREE
A falling tree can seriously damage anything it
may hit a car, a house, a fence a power line or
another tree. There are ways to make a tree fall
where you want it, so first decide where that is!
Before cutting, clear the area around the tree.
You will need good footing while working and
you should be able to work the saw without
hitting any obstacles.
Next select a path of retreat. When the tree
begins to fall you should retreat away from the
direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See
figure A).
Begin the cut on the side to which the tree is to
fall. Cut a notch approximately 1/3 of the way
into the tree. (See figure B). The position of this
notch is important since the tree will
try to fall “into” the notch. (See figure B).
The felling cut is made on the side opposite
the notch. Make the felling cut placing spiked
bumper 2.5 cm to 5cm above the bottom of the
notch and stop cutting at approximately 1/10
of diameter to the inner edge of the notch (See
figure C) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the
felling cut. The remaining wood between the
notch cut and felling cut will act as a hinge when
the tree falls, guiding it in the desired direction.
When the tree starts to fall, stop the engine,
place the saw on the ground and make your
retreat quickly.
To fell a big tree with a diameter exceeding twice
the bar length start the notching cuts from one
side and draw the saw through to the other side
of the notch.
Start the back cut on one side of the tree with
spiked bumper engaged, pivoting the saw
through to from the desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as
not to cause kickback.
The final cut is made by drawing the saw forward
in the cut to reach the hinge. (See figure D).
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure A
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure B
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure C
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure D
14
GENERAL CUTTING INSTRUCTIONS
(CONTINUED)
Start the engine, see that is running properly.
Squeeze the trigger to open the throttle wide
open, then start the cut. It is not necessary to
press down hard to make the saw cut. If the
chain is properly sharpened, the cutting
should be relatively effortless. Pushing the saw
too hard will slow the engine and cutting will
actually be more difficult.
Some material may adversely affect the housing
of your chain saw.
(Example: palm tree acid, fertilizer etc.)
To avoid housing deterioration carefully remove
all packed saw dust around clutch and guide bar
area and wash with water.
WARNING DANGER
Do not let the nose or tip of the guide bar touch
anything while the engine is running to avoid
kickback.
FELLING A TREE
A falling tree can seriously damage anything it
may hit a car, a house, a fence a power line or
another tree. There are ways to make a tree fall
where you want it, so first decide where that is!
Before cutting, clear the area around the tree.
You will need good footing while working and
you should be able to work the saw without
hitting any obstacles.
Next select a path of retreat. When the tree
begins to fall you should retreat away from the
direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See
figure A).
Begin the cut on the side to which the tree is to
fall. Cut a notch approximately 1/3 of the way
into the tree. (See figure B). The position of this
notch is important since the tree will
try to fall “into” the notch. (See figure B).
The felling cut is made on the side opposite
the notch. Make the felling cut placing spiked
bumper 2.5 cm to 5cm above the bottom of the
notch and stop cutting at approximately 1/10
of diameter to the inner edge of the notch (See
figure C) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the
felling cut. The remaining wood between the
notch cut and felling cut will act as a hinge when
the tree falls, guiding it in the desired direction.
When the tree starts to fall, stop the engine,
place the saw on the ground and make your
retreat quickly.
To fell a big tree with a diameter exceeding twice
the bar length start the notching cuts from one
side and draw the saw through to the other side
of the notch.
Start the back cut on one side of the tree with
spiked bumper engaged, pivoting the saw
through to from the desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as
not to cause kickback.
The final cut is made by drawing the saw forward
in the cut to reach the hinge. (See figure D).
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure A
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure B
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure C
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure D
15
LIMBING
Never limb on the tree that you are standing. Be
careful of the tip touching other limbs. Always
use both hands.
Don’t cut with the saw overhead or the bar in a
vertical position. If the saw should kickback, you
may not have good enough control to prevent
possible injury.
CAUTION
Do not saw above chest height.
BUCKING
Bucking is the sawing of a log or fallen tree into
smaller pieces.
There are a few basic rules which apply to all
bucking operations. Keep both hands on the
handles at all times. Support logs if possible.
When cutting on a slope or hillside, always stand
uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
USING THE PRODUCT
14
GENERAL CUTTING INSTRUCTIONS
(CONTINUED)
Start the engine, see that is running properly.
Squeeze the trigger to open the throttle wide
open, then start the cut. It is not necessary to
press down hard to make the saw cut. If the
chain is properly sharpened, the cutting
should be relatively effortless. Pushing the saw
too hard will slow the engine and cutting will
actually be more difficult.
Some material may adversely affect the housing
of your chain saw.
(Example: palm tree acid, fertilizer etc.)
To avoid housing deterioration carefully remove
all packed saw dust around clutch and guide bar
area and wash with water.
WARNING DANGER
Do not let the nose or tip of the guide bar touch
anything while the engine is running to avoid
kickback.
FELLING A TREE
A falling tree can seriously damage anything it
may hit a car, a house, a fence a power line or
another tree. There are ways to make a tree fall
where you want it, so first decide where that is!
Before cutting, clear the area around the tree.
You will need good footing while working and
you should be able to work the saw without
hitting any obstacles.
Next select a path of retreat. When the tree
begins to fall you should retreat away from the
direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See
figure A).
Begin the cut on the side to which the tree is to
fall. Cut a notch approximately 1/3 of the way
into the tree. (See figure B). The position of this
notch is important since the tree will
try to fall “into” the notch. (See figure B).
The felling cut is made on the side opposite
the notch. Make the felling cut placing spiked
bumper 2.5 cm to 5cm above the bottom of the
notch and stop cutting at approximately 1/10
of diameter to the inner edge of the notch (See
figure C) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the
felling cut. The remaining wood between the
notch cut and felling cut will act as a hinge when
the tree falls, guiding it in the desired direction.
When the tree starts to fall, stop the engine,
place the saw on the ground and make your
retreat quickly.
To fell a big tree with a diameter exceeding twice
the bar length start the notching cuts from one
side and draw the saw through to the other side
of the notch.
Start the back cut on one side of the tree with
spiked bumper engaged, pivoting the saw
through to from the desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as
not to cause kickback.
The final cut is made by drawing the saw forward
in the cut to reach the hinge. (See figure D).
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure A
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure B
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure C
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure D
14
GENERAL CUTTING INSTRUCTIONS
(CONTINUED)
Start the engine, see that is running properly.
Squeeze the trigger to open the throttle wide
open, then start the cut. It is not necessary to
press down hard to make the saw cut. If the
chain is properly sharpened, the cutting
should be relatively effortless. Pushing the saw
too hard will slow the engine and cutting will
actually be more difficult.
Some material may adversely affect the housing
of your chain saw.
(Example: palm tree acid, fertilizer etc.)
To avoid housing deterioration carefully remove
all packed saw dust around clutch and guide bar
area and wash with water.
WARNING DANGER
Do not let the nose or tip of the guide bar touch
anything while the engine is running to avoid
kickback.
FELLING A TREE
A falling tree can seriously damage anything it
may hit a car, a house, a fence a power line or
another tree. There are ways to make a tree fall
where you want it, so first decide where that is!
Before cutting, clear the area around the tree.
You will need good footing while working and
you should be able to work the saw without
hitting any obstacles.
Next select a path of retreat. When the tree
begins to fall you should retreat away from the
direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See
figure A).
Begin the cut on the side to which the tree is to
fall. Cut a notch approximately 1/3 of the way
into the tree. (See figure B). The position of this
notch is important since the tree will
try to fall “into” the notch. (See figure B).
The felling cut is made on the side opposite
the notch. Make the felling cut placing spiked
bumper 2.5 cm to 5cm above the bottom of the
notch and stop cutting at approximately 1/10
of diameter to the inner edge of the notch (See
figure C) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the
felling cut. The remaining wood between the
notch cut and felling cut will act as a hinge when
the tree falls, guiding it in the desired direction.
When the tree starts to fall, stop the engine,
place the saw on the ground and make your
retreat quickly.
To fell a big tree with a diameter exceeding twice
the bar length start the notching cuts from one
side and draw the saw through to the other side
of the notch.
Start the back cut on one side of the tree with
spiked bumper engaged, pivoting the saw
through to from the desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as
not to cause kickback.
The final cut is made by drawing the saw forward
in the cut to reach the hinge. (See figure D).
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure A
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure B
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure C
FELLING A TREE
A falling tree can seriously damage anything it may hit a
car, a house, a fence a powerline or another tree.
There are ways to make a tree fall where you want it, so
first decide where that is!
Before cutting, clear the area around the tree. You will
need good footing while working and you should be
able to work the saw without hitting any obstacles.
Next select a path of retreat.
When the tree begins to fall you should retreat away
from the direction of fall at a 45-degree angle to avoid
the trunk kicking back over the stump. (See right above
figure)
Begin the cut on the side to which the tree is to fall.
Cut a notch approximately 1/3 of the way into the tree.
(See figure A)
The position of this notch is important since the tree will
try to fall “into” the notch. (See figure A)
The felling cut is made on the side opposite the notch.
Make the felling cut placing spiked bumper 2.5 cm to
5cm above the bottom of the notch and stop cutting at
approximately 1/10 of diameter to the inner edge of the
notch (See figure B) in order to leave the uncut portion
of the wood as a hinge.
Do not try to cut through to the notch with the felling
cut. The remaining wood between the notch cut and
felling cut will act as a hinge when the tree falls, guiding
it in the desired direction.
When the tree starts to fall, kill the engine, place the
saw on the ground and make your retreat quickly.
To fell big tree with a diameter exceeding twice the bar
length start the notching cuts from one side and draw
the saw through to the other side of the notch.
Start the back cut on one side of the tree with spiked
bumper engaged, pivoting the saw through to from the
desired hinge on that side.
Then remove the saw for the second cut.
Insert the saw in the first cut very carefully so as not to
cause kickback.
The final cut is made by drawing the saw forward in the
cut to reach the hinge. (See figure C)
Figure D
15
LIMBING
Never limb on the tree that you are standing. Be
careful of the tip touching other limbs. Always
use both hands.
Don’t cut with the saw overhead or the bar in a
vertical position. If the saw should kickback, you
may not have good enough control to prevent
possible injury.
CAUTION
Do not saw above chest height.
BUCKING
Bucking is the sawing of a log or fallen tree into
smaller pieces.
There are a few basic rules which apply to all
bucking operations. Keep both hands on the
handles at all times. Support logs if possible.
When cutting on a slope or hillside, always stand
uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
15
LIMBING
Never limb on the tree that you are standing. Be
careful of the tip touching other limbs. Always
use both hands.
Don’t cut with the saw overhead or the bar in a
vertical position. If the saw should kickback, you
may not have good enough control to prevent
possible injury.
CAUTION
Do not saw above chest height.
BUCKING
Bucking is the sawing of a log or fallen tree into
smaller pieces.
There are a few basic rules which apply to all
bucking operations. Keep both hands on the
handles at all times. Support logs if possible.
When cutting on a slope or hillside, always stand
uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
15
LIMBING
Never limb on the tree that you are standing. Be
careful of the tip touching other limbs. Always
use both hands.
Don’t cut with the saw overhead or the bar in a
vertical position. If the saw should kickback, you
may not have good enough control to prevent
possible injury.
CAUTION
Do not saw above chest height.
BUCKING
Bucking is the sawing of a log or fallen tree into
smaller pieces.
There are a few basic rules which apply to all
bucking operations. Keep both hands on the
handles at all times. Support logs if possible.
When cutting on a slope or hillside, always stand
uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
15
LIMBING
Never limb on the tree that you are standing. Be
careful of the tip touching other limbs. Always
use both hands.
Don’t cut with the saw overhead or the bar in a
vertical position. If the saw should kickback, you
may not have good enough control to prevent
possible injury.
CAUTION
Do not saw above chest height.
BUCKING
Bucking is the sawing of a log or fallen tree into
smaller pieces.
There are a few basic rules which apply to all
bucking operations. Keep both hands on the
handles at all times. Support logs if possible.
When cutting on a slope or hillside, always stand
uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
LIMBING
BUCKING
Limbing a fallen tree is much the same as bucking.
Never limb on the tree that you are standing.
Be careful of the tip touching other limbs.
Always use both hands.
Don’t cut with the saw overhead or the bar in a vertical
position. If the saw should kickback, you may not have
good enough control to prevent possible injury.
CAUTION
Don’t saw above chest height.
Bucking is the sawing of a log or fallen tree into smaller
pieces.
There are a few basic rules which apply to all bucking
operations.
Keep both hands on the handles at all times.
Support logs if possible.
When cutting on a slope or hillside, always stand uphill.
CAUTION
Stay on the uphill side of logs.
Содержание BRUZCS4210
