background image

 

and the debris shield. This results in the debris 

being thrown 

AWAY

 from you. (Fig. 10).

      

       WARNING / DANGER

Tilting the head to the wrong side will shoot the  

debris TOWARDS you. If the line head is held flat 

to the ground so that cutting occurs on the whole  

line circle, debris will be THROWN at you, drag 

will slow the engine down, and you will use up a 

lot of line.

       WARNING / DANGER

Use only quality nylon mono-filament line of

the  diameter 2.4mm. Never use wire or wire-

reinforced line in place of nylon trimmer line. 

Load your nylon line cutting head only with nylon 

trimmer line of the proper diameter. For the Bent 

Shaft Trimmer we recommend 2.0 - 2.4mm.

       WARNING / DANGER

All model trimmers and brush cutters can throw 

small stones, metal or small objects as well as 

the material being cut. Read these 

Rules for Safe 

Operation

 with care. 

Follow the instructions in your operators manual.

Read the operator’s manual carefully. Be 

thoroughly familiar with the controls and proper 

use of the unit. Know how to stop the unit and 

shut off the engine. Know how to unhook 

a harnessed unit quickly.

Never allow anyone to use the unit without proper 

instruction. Be sure the operator wears foot, leg, 

eye, face and hearing protection. Do not rely on 

the debris shield on the unit to protect your eyes 

from ricocheting or thrown objects. Keep the area 

clear of bystanders, children and pets. Never al-

low children to operate or play with the unit.

       WARNING / DANGER

In addition to head, eye, face and ear protectors 

shoes should be worn to protect your feet and 

improve your footing on slippery surfaces. Do not 

wear ties, jewelry, or loose, dangling clothing 

which could be caught in the unit.

Do not wear open-toed footwear, or go barefoot or 

bare legged. In certain situations you must wear 

total face and head protection. Pay attention to 

kick back and blade thrust.

Do not  allow anyone to  enter the  operating 

Danger Zone 

with you. The 

Danger Zone 

 is an 

area 15 meters in radius (about 16 paces) or 

50 feet. Insist  that  persons in the 

Risk Zone 

  

beyond the 

Danger Zone 

 wear eye protection 

from thrown objects.  If  the  unit  must  be  used  

where  there are unprotected people, operate at 

a low throttle speed to reduce the risk of thrown 

objects. Move the  stop switch to “stop” position 

when the engine idles. Continue to operate the 

unit only when the stop switch is in good working 

condition. Ensure that the cutting attachment 

stops turning when the engine idles.

No persons except for operator is allowed within 

a 15 metre radium of the 

Danger Zone. 

Eye, 

Ear, Face, Foot, Leg and Body protection must 

be worn by operator. Persons in danger zone or 

beyond 

Danger Zone 

should wear eye protection 

against thrown objects. Risk diminishes with 

distance from the 

Danger Zone.

RULES FOR SAFE OPERATION

CUTTING WITH A NYLON HEAD

Line head rotates in a 

CLOCKWISE

 direction. The 

CUT-OFF KNIFE

 will be on the 

right side of the debris shield

       WARNING / DANGER 

Cutting with a Nylon Head 

The proper debris shield must be in place on the 

unit when nylon cutting line is used. The cutting 

line can flap around if too much line is exposed. 

Always use the plastic debris shield with cut-off 

knife when using nylon cutting heads.

 

For nearly all cutting, it is good to tilt the line head 

so that contact is made on the part of the line 

circle where the line is moving 

AWAY

 from you -

       

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Clock Wise Roatation

Debris

Cut on 

this side

Содержание B2600





















Отзывы: