Bush DLED65UHDHDRSA, Инструкция по эксплуатации

Страница: 38 / 64

• The location where the transmission is most effective differs
depending on the usage environment.
• The Wireless feature of the TV supports 802.11 a,b,g & n
type modems. It is highly recommended that you should
use the IEEE 802.11n communication protocol in order to
avoid any possible problems while watching videos.
• You must change your modem’s SSID when there are
any other modems around with the same SSID. You can
encounter connection problems otherwise. Use a wired
connection if you experience problems with a wireless
connection.
Configuring Wireless Device Settings
Open the Network menu and select Network Type as
Wireless Device
to start connection process.
Highlight
Scan Wireless Networks
option and press
OK
to start a search for available wireless networks. All found
networks will be listed. Highlight your desired network
from the list and press
OK
to connect.
Note:
If the modem supports N mode, you should set
N mode settings.
If the selected network is password-protected, enter the
correct key by using the virtual keyboard. You can use this
keyboard via the directional buttons and the
OK
button on
the remote control.
Wait until the IP address is shown on the screen.
This means that the connection is now established. To
disconnect from a wireless network, highlight
Network
Type and press Left or Right buttons to set as Disabled .
If your router has WPS, you can directly connect to the
modem/router without entering a password or adding the
network first. Highlight
Press WPS on your wifi router
option and press OK . Go to your modem/router device
and press the WPS button on it to make the connection.
You will see a connection confirmation on your TV once
the devices have paired. Select
OK
to proceed. No further
configuration is required.
Highlight
Internet Speed Test and press the OK button to
check your internet connection speed. Highlight Advanced
Settings
and press the
OK
button to open the advanced
setting menu. Use directional and numeric buttons to set.
Highlight
Save and press the OK button to save settings
when complete.
Other Information
The status of the connection will be displayed as
Connected or Not Connected and the current IP address,
if a connection is established.
Connecting to your mobile device via WLAN
• If your mobile device has WLAN feature, you can
connect it to your TV via a router, in order to access
the content in your device. For this, your mobile device
must have an appropriate sharing software.
Connect your TV to your router following the steps
mentioned in the section above.
Afterwards, connect your mobile device to the router and
then activate the sharing software on your mobile device.
Then, select files that you want to share with your TV.
If the connection is established correctly, you will be able to
access the shared files installed on your mobile device via the
Audio Video Sharing (AVS) feature of your TV.
Highlight the
AVS
option in the Sources menu and press
OK
, available media server devices in the network will be
displayed. Select your mobile device and press the OK button
to continue.
• If available, you can download a virtual remote controller
application from the server of your mobile device
application provider.
Note: This feature may not be supported on all mobile
devices.
Networked Standby Mode
Networked Standby Mode is a standard that allows
a device to be turned on or woken up by a network
message. The message is sent to the device by a program
executed on a remote device connected to the same
local area network, such as a smartphone.
To enable this feature set the
Networked Standby Mode
option in the Network menu as On . It is necessary that
both the device, from which the network message will
be sent to the TV, and the TV are connected to the
same network. Networked Standby Mode feature is only
supported for Android OS devices and can only be used
via a variety of applications.
In order to use this feature the TV and the remote device
should be connected at least once while the TV is on.
If the TV is powered off, the connection should be re-
established, the next time it is switched on. Otherwise this
feature will be unavailable. This does not apply, when the
TV is switched into the standby mode.
If you want your TV to consume less power in standby
mode, you can disable this feature by setting the
Networked Standby Mode option as
Off
.
Advanced features
Getting the most from your TV
Advanced features 36
If you require any technical guidance or find that your TV is not operating as intended, a simple solution can often be found in the
Troubleshooting
section of these instructions,
or online at www.bush-support.co.uk. If you still require further assistance, call one of our experts on 0345 604 0105, a Bush enquiry line.