BUSCH R 5 RA 1000 B Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 40

background image

Storage | 4

0870201062_RA1000-1600B_Ex_-0007_IM_en

11 / 40

4

Storage

• Seal all apertures with adhesive tape or reuse provided caps.

Version with water-oil heat exchanger:

• Make sure that the cooling water has been completely removed, see

.

If the machine is to be stored for more than 3 months:

• Wrap the machine in a corrosion inhibiting film.

• Store the machine indoors, dry, dust free and if possible in original packaging

preferably at temperatures between 0 ... 40 °C.

5

Installation

5.1 Installation Conditions

WARNING

The installation conditions are not respected in an ATEX environment.

Risk of severe injury!

Risk of explosion!

• Take care that the installation conditions are met.

NOTICE

Use of the machine outside of the permitted installation conditions.

Risk of premature failure!

Loss of efficiency!

• Take care that the installation conditions are fully complied with.

~50 cm

~50 cm

~100 cm

~100 cm

• Make sure that the environment of the machine complies with the ATEX classification

of the machine according to the data given on the nameplate of the motor and the
nameplate of the machine (NP).

• Make sure that the ambient conditions comply with the

Technical Data [

• Make sure that the environmental conditions comply with the protection class of the

motor and the electrical instruments.

«
...
9
10
11
12
13
...
»

Содержание R 5 RA 1000 B









































Отзывы:

Нет отзывов

Похожие инструкции для R 5 RA 1000 B

Бренд: A.O. Smith Страницы: 20

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 24

Бренд: A.O. Smith Страницы: 6

Бренд: A.O. Smith Страницы: 2

Бренд: A.O. Smith Страницы: 2

Бренд: xFyre Страницы: 60

Бренд: A.O. Smith Страницы: 8

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 6

Бренд: A.O. Smith Страницы: 40

Бренд: Zip Страницы: 16

Бренд: Watson Marlow Pumps Страницы: 95

Бренд: Watson Marlow Pumps Страницы: 87

Бренд: Watson Marlow Pumps Страницы: 127

Бренд: ubbink Страницы: 31

Бренд: OEG Страницы: 28

Бренд: Envision Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды