Burkert 8695 Series Скачать руководство пользователя страница 9

Страница: 9 / 68

Basic safety instructions

BASIC SAFETY INSTRUCTIONS

These safety instructions do not consider any contingencies or incidents which occur during installation,

operation and maintenance.
The operator is responsible for observing the location-specific safety regulations, also with reference to the

personnel.

DANGER

Risk of injury from high pressure and discharge of medium.

▶

Before working on the device or system, switch off the pressure. Vent or drain lines.

DANGER

Risk of injury from electric shock.

▶

Before working on the device or system, switch off the power supply. Secure against reactivation.

▶

Observe applicable accident prevention and safety regulations for electrical equipment.

To prevent injury, ensure the following:

▶

Secure device or system to prevent unintentional activation.

▶

Only trained technicians may perform installation and maintenance work.

▶

Perform installation and maintenance with suitable tools only.

▶

Do not make any changes to the device and do not subject it to mechanical stress.

▶

Operate the device only in perfect state and in consideration of the operating instructions.

▶

Observe the general rules of technology.

▶

Install the device according to the regulations applicable in the respective country.

▶

Do not feed corrosive or flammable media into the device connections.

▶

Do not feed any fluids into the connections of the device.

▶

After the process is interrupted, restart in a controlled manner. Observe sequence:

1. Connect electrical or pneumatic power supply.

2. Charge the device with medium.

▶

Observe intended use.

▶

When unscrewing and screwing in the body casing or the transparent cap, do not hold the actuator of the

process valve but the basic housing of the device.

english

Type 8695 REV.3

Содержание 8695 Series





































































Результаты поиска

Содержание 8695 Series

Отзывы:

Бренды по названию

Популярные бренды

Burkert 8695 Series, Руководство по эксплуатации

Результаты поиска

Содержание 8695 Series

Отзывы:

Бренды по названию

Популярные бренды