Burkert 8695 Series Скачать руководство пользователя страница 41

Страница: 41 / 68

Start-up

ATTENTION

Breakage of the pneumatic connection pieces due to rotational impact.

▶

When opening or closing the device, do not press against the actuator, but against the basic housing.

→

Open the device: turning the transparent cap anti-clockwise.

Status indicator

(RGB LED)

ASi PWR LED (green)

ASi FAULT LED (red)

Key 2

Key 1

büS service interface

Inv.ValveDir. LED

Manual LED

Pilot LED

Figure 28:

Operating and display elements

0 s

5 s

10 s

Manual LED

Inv.ValveDir. LED

Start automatic

teach function

Status indicator

End of teach function

Figure 29:

Start automatic teach function

→

Press and hold key 1 for > 5 s to start the automatic teach function. The red manual LED and the green

Inv.ValveDir. LED flash for 5 s at 5 Hz.

→

When the red manual LED and the green Inv.ValveDir. LED start flashing faster (10 Hz), release key 1

within the next 5 s.

The status indicator flashes orange while the automatic teach function is running (function check). When

the status indicator stops flashing orange, the teach function is complete.

The end positions of the valve have been identified and saved.

Note: If the status indicator is lit red, the teach function is faulty and must be repeated.

ATTENTION

Damage or malfunction due to ingress of dirt or moisture.

To observe the degree of protection IP65 or IP67:

▶

Screw in transparent cap to the stop.

→

Close the device (see accessories for assembly tool).

english

Type 8695 REV.3

Содержание 8695 Series





































































Результаты поиска

Содержание 8695 Series

Отзывы:

Бренды по названию

Популярные бренды

Burkert 8695 Series, Руководство по эксплуатации

Результаты поиска

Содержание 8695 Series

Отзывы:

Бренды по названию

Популярные бренды