Burkert 8695 Series Скачать руководство пользователя страница 13

Страница: 13 / 68

Technical data

TECHNICAL DATA

6.1

Standards and directives

The device complies with the relevant EU harmonisation legislation. In addition, the device also complies

with the requirements of the laws of the United Kingdom.
The harmonised standards that have been applied for the conformity assessment procedure are listed in the

current version of the EU Declaration of Conformity/UK Declaration of Conformity.

6.2

Licenses

The product is approved for use in zone 2 and 22 in accordance with ATEX directive 2014/34/EU category

3GD.

Observe instructions on operation in a

potentially explosive atmosphere

(Ex area).

Observe the ATEX additional instructions.

The product is cULus approved. Instructions for use in the UL area see chapter

“6.7 Electrical data”.

6.3

Operating conditions

WARNING!

Solar radiation and temperature fluctuations may cause malfunctions or leaks.

▶

If the device is used outdoors, do not expose it unprotected to the weather conditions.

▶

Ensure that the permitted ambient temperature does not exceed the maximum value or drop below the

minimum value.

Ambient temperature

see type label

Degree of protection

Evaluated by the manufacturer:

Evaluated by UL:

IP65 / IP67 according to EN 60529

UL Type 4x Rating, indoor only

Operating altitude

up to 2000 m above sea level

Relative air humidity

max. 90% at 55 °C / 60 °C (non condensing)

Only if cables, plugs and sockets have been connected correctly and in compliance with the exhaust air concept see

chapter “8 Pneumatic installation”.

english

Type 8695 REV.3

Содержание 8695 Series





































































Результаты поиска

Содержание 8695 Series

Отзывы:

Бренды по названию

Популярные бренды

Burkert 8695 Series, Руководство по эксплуатации

Результаты поиска

Содержание 8695 Series

Отзывы:

Бренды по названию

Популярные бренды