Bunn ingle Multi- BrewWISEDBC WITH SMART FUNNELTM страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 50

background image

Page 45

TROUBLESHOOTING (cont.)
Problem

Possible Cause

Troubleshooting Procedures

Check the sensitivity setting. Refer
to the

Refill function on page 31. If

the left three digit number is less
than the right number, the machine
“thinks” it is full and the refill valve
should be off. If the left number is
larger than the right, then the refill
valve will automatically be turned on
to fill the tank. The right number is
the threshold setting and can be
adjusted to compensate for extreme
water conditions: very pure, low
conductance water requires a higher
setting, while high mineral content,
high conductance water requires a
lower setting. Note that the left num-
ber changes from a high value when
water is NOT touching the refill probe
to a low value when water IS touch-
ing the probe. For best operation,
the right number should be set to a
value midway between these low
and high numbers. Before changing
the setting, confirm that the refill
probe is free of scale buildup and the
connection to it is secure.

Substitute a control board known to
be in good working order.

Remove power from the brewer.
Press reset button on limit thermo-
stat. Then check for continuity
through it.

Remove power from the brewer.
Check for continuity through the tank
heaters.

1. Refill Probe or Sensitivity Setting

2. Electronic Control Board

1. Limit Thermostat

CAUTION -

Do not eliminate or by-

pass limit thermostat. Use only re-
placement part #23717.0001.

2. Tank Heaters

Water flows into tank continuously
with power applied to brewer.

Water will not heat or display shows
HEATING TIME TOO LONG

37467 110904

«
...
43
44
45
46
47
...
»

Содержание ingle Multi- BrewWISEDBC WITH SMART FUNNELTM



















































Отзывы:

Нет отзывов

Похожие инструкции для ingle Multi- BrewWISEDBC WITH SMART FUNNELTM

Бренд: Yoer Страницы: 32

Бренд: Massimo Zanetti Страницы: 58

KM 160 Minimo Premio

Бренд: ECG Страницы: 98

Бренд: Fellow Страницы: 23

Бренд: Krups Страницы: 16

Бренд: Necta Страницы: 44

Бренд: Faber Страницы: 28

Inissia EN 80.B

Бренд: DeLonghi Страницы: 13

Бренд: Zojirushi Страницы: 17

Бренд: Koenic Страницы: 71

Бренд: Saeco Страницы: 88

Бренд: Camp4 Страницы: 44

Бренд: Schaerer Страницы: 2

Бренд: Texlabel Страницы: 33

Бренд: Sencor Страницы: 10

Бренд: BRAYER Страницы: 17

ESPRESSO COFFEE MACHINE

Бренд: ZAGATO Страницы: 16

Бренд: Saeco Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды