Bunn ingle Multi- BrewWISEDBC WITH SMART FUNNELTM страница 9 Скачать руководство пользователя | Manualshive

Страница: 9 / 50

background image

Page 9

INITIAL SETUP

CAUTION –

The brewer must be disconnected from the power source throughout the initial setup, except when

specified in the instructions.
1. Insert an empty funnel into the funnel rails of the brew station.
2. Place an empty server under the funnel.
3. Connect the brewer to the power source. Water will begin flowing into the tank and stop when the tank is filled

to its capacity. Display will show

PLEASE WAIT...TANK FILLING

until tank is filled with water.

4. Wait approximately twenty minutes for the water in the tank to heat to the proper temperature. Display will show

READY TO BREW...WATER TEMP: XXX˚

when tank is at operating temperature.

5. Place a small vessel beneath the faucet and open the faucet handle. Release it when you hear the tank refilling.
6. Water volumes have been preset at the factory. Refer to adjustments for the

Set Brew Volumes section of this

manual should the volume need to be increased or decreased.

7. The brewer is now ready for use in accordance with the coffee brewing instructions.

COFFEE BREWING

1. Select the desired recipe on the grinder. It is not necessary to select a recipe on the brewer.
2. Insert a BUNN

filter into the funnel.

3. Grind the proper amount of fresh coffee into the Smart Funnel

using the Multi-BrewWISE DBC grinder with

Smart Funnel

operation and level the grounds by gently shaking.

4. Slide the funnel into the funnel rails. The brewer will read the recipe ground through the chip in the funnel handle

and will automatically select the correct recipe to brew. If the grounds are not obtained through a grinder
compatible with a Smart Funnel, a recipe must be chosen on the brewer.

5. Place an empty server under the funnel.
6. Press the "ON/OFF/POWER" pad and release.
7. Press the "ON/OFF/LOWER" warmer pad and release.
8

Momentarily press and release the "BREW" pad. If the brewer has the funnel lock option and if it is activated,
once a brew cycle has been started the funnel is locked in place. There may be certain situations in which the
brew cycle will not begin when "BREW" is pressed:

a)

BREW TEMPERATURE TOO LOW

- wait until heated or cancel

BREW LOCKOUT

option. (Page 13)

b)

FUNNEL NOT PRESENT

(or using a standard brew funnel) - cancel

FUNNEL LOCKOUT

option. (Page 34)

c)

CHECK FUNNEL

- remove funnel, empty previously brewed grounds and grind a new batch into the funnel.

d)

SWITCH NOT ON

- Press the "ON/OFF/LOWER" warmer pad to ON and release. (Page 36)

9. If none of the above messages are displayed, the display will read

NOW BREWING

.

10. Following the BREW will be a countdown of drip time

DRIPPING

which shows the time remaining for drip-out

until the funnel lock will release. Discard the grounds and filter only after visible dripping stops.

CLEANING

1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all

surfaces on Bunn-O-Matic equipment.

2. Check and clean the sprayhead. The sprayhead holes must always remain open.

NOTE –

In hard water areas, this may need to be done daily. It will help prevent liming problems in the brewer and

takes less than a minute.

37467 110904

«
...
7
8
9
10
11
...
»

Содержание ingle Multi- BrewWISEDBC WITH SMART FUNNELTM



















































Отзывы:

Нет отзывов

Похожие инструкции для ingle Multi- BrewWISEDBC WITH SMART FUNNELTM

STILISTA PRIMEO

Бренд: Martello Страницы: 20

Бренд: Pacific Страницы: 13

Бренд: Vitek Страницы: 116

PALOMA 647001.00

Бренд: Tescoma Страницы: 2

Бренд: DeLonghi Страницы: 78

Бренд: Bialetti Страницы: 88

Бренд: West Bend Страницы: 40

Бренд: Wilfa Страницы: 52

Бренд: Smach Страницы: 24

Бренд: Saeco Страницы: 18

Zia 7.000 Series

Бренд: de Jong Duke Страницы: 34

Бренд: Oki Страницы: 140

Бренд: TREVIDEA Страницы: 24

G3FERRARI Cafexpress G20076

Бренд: TREVIDEA Страницы: 28

Бренд: Philips Страницы: 24

Бренд: Nevir Страницы: 23

SMART BREAD MAKER

Бренд: Sana Страницы: 60

Бренд: Trisa Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды