Bunn Crescendo Series Скачать руководство пользователя страница 2

2

52384.1  031314

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corp. (“BUNN”) warrants the BUNN Crescendo as further described below for a warranty period of 1 year parts 

and labor.

These warranty periods run from the date of installation. BUNN warrants that the equipment manufactured by it will be com-

mercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable 

warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, 

in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance 

or repair, non periodic cleaning and descaling, equipment failures related to poor water quality, damage or casualty. This war-

ranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone at 

(217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN,

shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from 

BUNN that the defective equipment is under warranty. Additionally, the following is excluded from the warranty period:

Warranty Exclusions:

•  Parts such as, but not limited to, hoppers and lids, drip trays, and plastic parts damaged due to improper handling or 

cleaning agents.

•  Replacement of wear items such as, but not limited to, O-rings, gaskets, silicone tubes, hoses, and valve seats.

•  Repairs made necessary due to poor water quality such as dispense valves, water inlet valves, scaling in the steam or hot 

water boilers. (Total Hardness recommended range of 4-7 gpg constant).

•  Improper voltage. (See equipment operations manual for voltage specifications).

•  Failure to use BUNN approved cleaning supplies constitutes improper maintenance.

•  Failure to have required preventive maintenance performed by BUNN technician or authorized espresso service provider.

•  Parts replaced under the terms of this warranty carry the remainder on the machine’s parts warranty term, or 60 days, 

whichever is greater.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS 

OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS 

FOR A PARTICULAR PURPOSE

. The agents, dealers or employees of BUNN are not authorized to make modifications to this  

warranty or to make additional warranties that are binding on BUNN.  Accordingly, statements by such individuals, whether oral or  

written, do not constitute warranties and should not be relied upon. If BUNN determines in its sole discretion that the equipment 

does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide 

at no charge replacement parts and/or labor (during the applicable parts and labor warranty periods specified above) to repair 

the defective components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace the 

equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS 

EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS  

SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND

. In no event shall BUNN be

liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of 

Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, 

incidental or consequential damages.

392, A Partner You Can Count On, Air Infusion, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, 

BrewWIZARD, BUNN Espress, BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red 

line, BUNNlink, Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. 

Brew stylized Dr. design, Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, 

Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect 

Earth with the stylized leaf and coffee cherry design, Safety-Fresh, vemycoffee.com, Scale-Pro, Silver Series, Single, Smart Fun-

nel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh, 

Titan, trifecta, TRIFECTA (sylized logo), Velocity Brew, Air Brew, Beverage Bar Creator, Beverage Profit Calculator, Brew better, 

not bitter., Build-A-Drink, BUNNSource, Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brewer Control, Element, 

Milk Texturing Fusion, Nothing Brews Like a BUNN, Picture Prompted Cleaning, Pouring Profits, Signature Series, Sure Tamp, 

Tea At Its Best, The Horizontal Red Line, Ultra are either trademarks or registered trademarks of Bunn-O-Matic Corporation. The 

commercial trifecta

®

 brewer housing configuration is a trademark of Bunn-O-Matic Corporation.

Содержание Crescendo Series

































Отзывы: