10
Adding Additional Remotes
Press and hold brake. Next, press and hold Button #1 on the working remote until the parking lights
flash once, release. Press and release Button #4 on the new remote. The parking lights will flash three
(3) times confirming that the new remote was learned.
Cold Start On and Off (Degree Select)
Press and hold brake. Next, press and hold Button #2 until the parking lights flash twice, release,
press and hold Button #2. Each parking light flash is a progression in degrees. Flash #1 is -40ºF, flash
#2 is -30ºF, flash #3 is -20ºF, flash #4 is -10ºF, flash #5 is 0ºF, flash #6 is +10ºF, flash #7 is +20ºF.
Two rapid flash parking light flashes is Cold Start Off. Release the brake, the parking lights will
flash three (3) times. NOTE: Factory setting is OFF.
Hot Start (Degree Select)
Press and hold the brake, then press and hold Button #2 (arm/disarm) until the parking lights flash
twice. Release Button #2. Press and hold Button #3, the parking lights will flash once. Each continuous
flash represents a progression in degrees: one (1) flash= 160ºF, two (2) flashes=150ºF, three (3)
flashes=140ºF, four (4) flashes=130ºF, five (5) flashes=120ºF, six (6) flashes=110ºF. To disable Hot Start,
press and hold Button #3 until the parking lights flash six (6) times, then two (2) quick flashes 7 and
8. The Hot Start is now disabled. Release the brake, the parking lights will flash three (3) times, the
programming is now entered. NOTE: The factory setting is Hot Start off. NOTE: Only Cold and Hot Start
functions can be enabled at the same time. If Button #1 is pressed for programming, Cold/Hot Start is
disabled. When Buttons #2 and #3 are pressed, then the Automatic and Low Voltage Starts are disabled.
Automatic Start - On
Press and hold brake. Press and hold Button #2 until the parking lights flash twice. Release. Press
and release Button #1. The parking lights will flash once. The automatic start is programmed ON. Release
the brake, the parking lights will flash three (3) times. NOTE: Factory setting is OFF.
Automatic Start - Off
Press and hold brake. Press and hold Button #2 until the parking lights flash twice. Release. Press
and release Button #1. The parking lights will flash twice. The automatic start is programmed OFF. Release
the brake, the parking lights will flash three (3) times. NOTE: Factory setting is OFF.
Tach Mode - ON
Press and hold the brake pedal. Press and hold Button #3 until the parking lights flash three (3) times.
Release. Press and release Button #4, the parking lights will flash twice. Release the brake, the parking
lights will flash three (3) times. The unit is now programmed for Tach Mode. NOTE: Factory setting is
Tachless Start ON.
Tachless Mode - ON
Press and hold the brake pedal. Press and hold Button #3 until the parking lights flash three (3) times,
release, press and release Button #4, the parking lights will flash once. Release the brake, the parking
lights will flash three (3) times. The unit is now programmed for Tachless Mode.
Tach Learn
To program your unit to Learn your tach signal. Press and hold the brake pedal, now press and hold Button
#2 until the parking lights flash twice. Release Button #2. Turn your ignition key to the RUN or ON position
while still holding the brake, press and hold Button #4 until the vehicle starts. After the engine starts,
release Button #4 to disengage the starter. Release the brake and turn the ignition OFF. After the Tach
Learn is complete, the unit will flash the parking lights once to show that the Tach Learn is now programmed.
Now try the remote starter, to be sure there is no over crank and the unit does crank long enough.
Programming Lock with Brake, Unlock with Ignition Off
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3)
times. Release Button #3. Press and release Button #2, the parking lights will flash once. The unit will
now lock with the brake and unlock when the ignition is turned off. Press and release Button #2 again,
the parking lights will flash twice. The Lock with Brake feature is now turned off. Release the brake,
the parking lights will flash three (3) times. The programming is now entered. NOTE: Factory setting is
Lock with Brake off.
Door Lock Pulse Length (Long) (For European type door locks)
Press and hold brake. Next, press and hold Button #3, the parking lights will flash three (3) times,
release, press and release Button #1. The parking lights will flash once, the door lock pulse length
will be 3.5 seconds. Release the brake, the parking lights will flash three (3) times.
Door Lock Pulse Length (Short) (For domestic type door locks)
Press and hold brake. Next, press and hold Button #3, the parking lights will flash three (3) times,
release, press and release Button #1. The parking lights will flash twice, the door lock pulse length
will be 0.7 seconds. Release the brake, the parking lights will flash three (3) times. NOTE: Factory
setting is SHORT pulse length.
Dual Pulse Door Lock
If your vehicle requires a Dual Pulse Lock output to lock the doors or to arm your factory alarm, you must
program your unit to do this. Press and hold the brake pedal, press and hold Button #3 until the parking
lights flash three (3) times. Release Button #3 then press Button #3 again and release. The parking lights
will flash once the unit is now programmed to dual pulse the lock output. Release the brake and the parking
lights will flash three (3) times. To turn Dual Pulse Lock off, repeat the above steps, then when you press
and release Button #3, the parking lights will flash twice. Release, the brake and the parking lights will
flash three (3) times.
Dual Pulse Door Unlock
If your vehicle requires a Dual Pulse Unlock output to unlock the doors or to disarm your factory alarm,
you must program your unit to do this. Press and hold the brake pedal, press and hold Button #4 until the
parking lights flash four (4) times. Release Button #4 then press Button #3 and release. The parking lights
will flash once the unit is now programmed to dual pulse the unlock output. Release the brake and the parking
lights will flash three (3) times. To turn Dual Pulse Unlock off, repeat the above steps, then when you
press and release Button #3, the parking lights will flash twice. Release the brake, the parking lights
will flash three
(3) times.
Programming Doorpin Inputs
Press and hold the brake, then press and hold Button #4, the parking lights will flash (4) times, release.
Now press and release Button #1. The parking lights will flash once, the unit is now programmed for a
(+) positive doorpin. Press and release Button #1 again, the parking lights will flash twice, the unit
is now programmed for a (-) negative doorpin.
Programming Runtime
Press and hold Button #4. The parking lights will flash once for every five (5) minutes you want the
engine to run. Release button at desired runtime. Maximum length, 25 minutes.
