HOW TO USE YOUR REMOTE TRANSMITTER
10
Automatic Start - On
Press and hold brake. Press and hold Button #2 until the parking lights flash twice. Release. Press
and release Button #1. The parking lights will flash once. The automatic start is programmed ON. Release
the brake, the parking lights will flash three (3) times. NOTE: Factory setting is OFF.
Automatic Start - Off
Press and hold brake. Press and hold Button #2 until the parking lights flash twice. Release. Press
and release Button #1. The parking lights will flash twice. The automatic start is programmed OFF. Release
the brake, the parking lights will flash three (3) times. NOTE: Factory setting is OFF.
Tach Mode - ON
Press and hold the brake pedal. Press and hold Button #3 until the parking lights flash three (3) times.
Release. Press and release Button #4, the parking lights will flash twice. Release the brake, the parking
lights will flash three (3) times. The unit is now programmed for Tach Mode. NOTE: Factory setting is
Tachless Start ON.
Tachless Mode - ON
Press and hold the brake pedal. Press and hold Button #3 until the parking lights flash three (3) times,
release, press and release Button #4, the parking lights will flash once. Release the brake, the parking
lights will flash three (3) times. The unit is now programmed for Tachless Mode.
Tach Learn
To program your unit to Learn your tach signal. Press and hold the brake pedal, now press and hold Button
#2 until the parking lights flash twice. Release Button #2. Turn your ignition key to the RUN or ON position
while still holding the brake, press and hold Button #4 until the vehicle starts. After the engine starts,
release Button #4 to disengage the starter. Release the brake and turn the ignition OFF. After the Tach
Learn is complete, the unit will flash the parking lights once to show that the Tach Learn is now programmed.
Now try the remote starter, to be sure there is no over crank and the unit does crank long enough.
Programming Lock with Brake, Unlock with Ignition Off
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3)
times. Release Button #3. Press and release Button #2, the parking lights will flash once. The unit will
now lock with the brake and unlock when the ignition is turned off. Press and release Button #2 again,
the parking lights will flash twice. The Lock with Brake feature is now turned off. Release the brake,
the parking lights will flash three (3) times. The programming is now entered. NOTE: Factory setting is
Lock with Brake off.
Door Lock Pulse Length (Long) (For European type door locks)
Press and hold brake. Next, press and hold Button #3, the parking lights will flash three (3) times,
release, press and release Button #1. The parking lights will flash once, the door lock pulse length
will be 3.5 seconds. Release the brake, the parking lights will flash three (3) times.
Door Lock Pulse Length (Short) (For domestic type door locks)
Press and hold brake. Next, press and hold Button #3, the parking lights will flash three (3) times,
release, press and release Button #1. The parking lights will flash twice, the door lock pulse length
will be 0.7 seconds. Release the brake, the parking lights will flash three (3) times. NOTE: Factory
setting is SHORT pulse length.
Dual Pulse Door Lock
If your vehicle requires a Dual Pulse Lock output to lock the doors or to arm your factory alarm, you must
program your unit to do this. Press and hold the brake pedal, press and hold Button #3 until the parking
lights flash three (3) times. Release Button #3 then press Button #3 again and release. The parking lights
will flash once the unit is now programmed to dual pulse the lock output. Release the brake and the parking
lights will flash three (3) times. To turn Dual Pulse Lock off, repeat the above steps, then when you press
and release Button #3, the parking lights will flash twice. Release, the brake and the parking lights will
flash three (3) times.
Dual Pulse Door Unlock
If your vehicle requires a Dual Pulse Unlock output to unlock the doors or to disarm your factory alarm,
you must program your unit to do this. Press and hold the brake pedal, press and hold Button #4 until the
parking lights flash four (4) times. Release Button #4 then press Button #3 and release. The parking lights
will flash once the unit is now programmed to dual pulse the unlock output. Release the brake and the parking
lights will flash three (3) times. To turn Dual Pulse Unlock off, repeat the above steps, then when you
press and release Button #3, the parking lights will flash twice. Release the brake, the parking lights
will flash three
(3) times.
Programming Doorpin Inputs
Press and hold the brake, then press and hold Button #4, the parking lights will flash (4) times, release.
Now press and release Button #1. The parking lights will flash once, the unit is now programmed for a
(+) positive doorpin. Press and release Button #1 again, the parking lights will flash twice, the unit
is now programmed for a (-) negative doorpin.
Programming Runtime
Press and hold Button #4. The parking lights will flash once for every five (5) minutes you want the
engine to run. Release button at desired runtime. Maximum length, 25 minutes.
Clearing the Memory of the Unit
Press and hold the brake pedal, now cycle the key in the ignition switch from OFF to RUN (not start)
five (5) times within four (4) seconds. Release the brake and try the remote. The unit should not function
with the remote. If the unit does not function, unplug the unit from both harnesses, wait one (1) minute
and plug it back in. Press Button #4 (stop) the parking lights will flash three (3) times, the unit is
now back to factory default and ready to operate. If memory does not clear, check to see if the heavy
gauge WHITE wire is on the proper ignition wire.
Starting the Vehicle with the Remote Transmitter
Press and release button #1 (start). The parking lights will flash once, confirming the car starter received the
signal. The car will then start and the parking lights will turn on and remain on while the vehicle is running. To
shut off the engine before the preset time, press Button #4, press the brake pedal or open the hood. NOTE: In tachless
mode, parking lights will wait approximately 10 seconds before turning on after the vehicle is running.
Pit Stop: Exiting the Car with the Engine Running
Make sure the transmission is in park; press Button #1 before turning the ignition switch off. (The engine will
remain running for the preset time.)
Keyless Entry Operation
Press Button #2, the system will arm, the doors will lock and the parking lights will flash once. Press Button #2
again, the system will disarm, the doors will unlock and the parking lights will flash twice. The parking lights
will remain on for one minute or until you turn the ignition on and press the brake.
Dome Light Option
The remote starter includes an optional output that can be used to operate the dome light when pressing Button #2,
unlock your power door locks. The dome light will remain on for one minute or until you turn the ignition on or
press the brake.
Trunk Release Output
The remote car starter includes an optional output from our unit that with a press and release of Button #3 will
give a pulse of (+) positive voltage for .75 seconds and if Button #3 is held down, this output will hold (+) positive
voltage on this wire until Button #3 is released. The parking lights will remain on for as long as this button is
held down. With a momentary press of this button the parking lights will flash once. This output can be used to
operate a power trunk release (Part #775 may be required for some imports and some domestics), power sliding doors
and rear lift gates (Part #775 may be required on some domestic and imported mini vans) operate a window roll up
module (Part #706 required) or operate a power sunroof (Part #775 may be required).
Runtime Confirmation (Engine Not Running)
To check programmed runtime, press and release Button #4, the parking lights will flash for the programmed length
of time. Each flash will equal 5 minutes of runtime. Example: Three parking light flashes represents 15 minutes of
runtime.
RS1300E:
BUTTON #1
Starts your vehicle.
BUTTON #2
Arms/Disarms your
system.
BUTTON #3
Pops your trunk
BUTTON #4
Shuts engine off and
programs runtime.
BULLDOG
Start
Arm
Disarm
Trunk
Stop
BULLDOG
RS1300E:
Starts your vehicle.
Arms/Disarms your
system.
Pops your trunk
Shuts engine off and
programs runtime.
