46
EN
M1.2.MRD500H.NLFREN - 08022018
Tightening tracks
With use, tracks tend to loosen. When operating with loose tracks, they tend
to slip over the driving wheel causing it to jump its housing or to work in
precarious situation, thus damaging wear to the housing.
To check track tightness, proceed as follows:
1.
Set the machine on a flat surface with compact ground, better on an
asphalt or stone pavement.
2. Lift the machine and set it on blocks or supports rated for the weight of the
machine so that the tracks are approximately 100 mm off the ground.
3. Measure the track midline vs. the horizontal line. The reading must not be
more than 10-15 mm.
If the distance is greater, proceed as follows:
1. Use the tipping handle to tip the dump box and set it on blocks or
supports rated for the weight of the box.
2. Loosen locknut A.
3. Tighten bolt B until the correct tightness is restored.
4. Secure bolt B by tightening locknut A thoroughly.
5. Return the dump box to its original position.
MINI TRACKED DUMPER
17
GB
Oil Drain Hose
Oil Filler
Remove the oil dipstick and add the oil. The
recommended hydraulic oil is 10W AW32,
ASLE H-150, or ISO 32. Tank Capacity is 3L.
Hydraulic Oil
Unscrew the locking nut to drain the oil into
the pan.
Tightening Tracks
With use, tracks tend to loosen. When
operating with loose tracks, they tend to slip
over the driving wheel causing it to jump its
housing, thus damaging wear to the housing.
To check track tightness, proceed as follows.
1. Set the machine on a flat surface with
compact ground, or on asphalt or pavement.
2. Lift the machine and set it on blocks or
supports rated for the weight of the machine
so that the tracks are approximately 10 cm
off the ground.
3. Measure the track midline vs. the horizontal
line. The reading must not be more than 10
~ 15 mm.
10 ~ 15 mm
If the distance is greater, proceed as follows.
1. Use the tipping handle to tip the hopper
and set it on blocks or supports rated for
the weight of the box.
2. Loosen locknut A.
3. Tighten bolt B until the correct tightness is
restored.
4. Secure bolt B by tightening locknut A
thoroughly.
5. Return the hopper to its original position.
09735UK00M110.indd 17
2017/12/20 16:56:51
WARNING!
•
Don’t over-tighten your track. The adjustment of the track and the brakes are linked, therefore
be very careful because if the track is over-tightened, the braking effect will be lost.
•
If the adjustment bolt has no more adjustment left, the tracks may have to be replaced.
MINI TRACKED DUMPER
18
GB
If the adjustment bolt has no more
adjustment left, the tracks may have
to be replaced.
Caution: Do not over-tighten your
track. The adjustment of the track
and the brakes are linked. The
braking power will lessen the more
the track is tightened.
Steering Wheel Axle
Steering Wheel
Adjusting Bolt
A
B
A
B
Replacing Tracks
Check the condition of the tracks periodically.
If any track is cracked or frayed, it should be
replaced as soon as convenient.
1. Lift up the hopper and insert a support rod
for safety purposes.
2. Lift the machine and set it on blocks or
supports rated for the weight of the machine
so that the tracks are approximately 10 cm
off the ground.
3. Remove the three M8
×
16 bolts and washers
that fix the track protection guard.
Support Object
Danger Area
Support Rod
M8
×
16
(
×
3)
09735UK00M110.indd 18
2017/12/20 16:56:58
MINI TRACKED DUMPER
18
GB
If the adjustment bolt has no more
adjustment left, the tracks may have
to be replaced.
Caution: Do not over-tighten your
track. The adjustment of the track
and the brakes are linked. The
braking power will lessen the more
the track is tightened.
Steering Wheel Axle
Steering Wheel
Adjusting Bolt
A
B
A
B
Replacing Tracks
Check the condition of the tracks periodically.
If any track is cracked or frayed, it should be
replaced as soon as convenient.
1. Lift up the hopper and insert a support rod
for safety purposes.
2. Lift the machine and set it on blocks or
supports rated for the weight of the machine
so that the tracks are approximately 10 cm
off the ground.
3. Remove the three M8
×
16 bolts and washers
that fix the track protection guard.
Support Object
Danger Area
Support Rod
M8
×
16
(
×
3)
09735UK00M110.indd 18
2017/12/20 16:56:58
copyrighted
document
- all
rights
reserved
by
FBC