45
EN
M1.2.MRD500H.NLFREN - 08022018
MINI TRACKED DUMPER
16
GB
Belt Cover
M6
×
12
(
×
2)
M6
×
12
(
×
2)
M8
×
20
(
×
2)
Belt Cover for Gearbox Pulley
Gearbox Pulley
M10
×
25
(
×
2)
M10
×
25
(
×
1)
M10
×
25
(
×
2)
Pump with Flange
Drive Belt
Replacing Drive Belt
Remove three belt covers as shown.
Remove the belt cover for gearbox pulley.
Disassemble the two M10
×
25 bolts, spring
washers and flat washers, remove the pump
with flange.
Turn the gearbox pulley and pull out the belt.
Lubrication
The gearbox is pre-lubricated and sealed
at the factory. No need to lubricate until 50
hours use.
After first 50 hours use, change all the
transmission oil. Capacity is 1.5L.
For future use, just check the oil level every 50
hours of working. If remove the drain plug, no
oil flow out, then add the oil.
Use portable tool lithium #0 grease such as
Lubriplate 6300AA , Lubriplate GR-132, or
Multifak, e.g. EP-O.
Transmission oil must be replace when engine
is stopped and warm by unscrewing filler cap
and drain plug. When oil is completely drained,
replace filler cap and fill up with fresh oil.
Oil Filler
Oil Outlet
09735UK00M110.indd 16
2017/12/20 16:56:47
Disassemble the two M10x25 bolts, spring washers and flat
washers, remove the pump with flange.
Turn the gearbox pulley and pull out the belt.
MINI TRACKED DUMPER
16
GB
Belt Cover
M6
×
12
(
×
2)
M6
×
12
(
×
2)
M8
×
20
(
×
2)
Belt Cover for Gearbox Pulley
Gearbox Pulley
M10
×
25
(
×
2)
M10
×
25
(
×
1)
M10
×
25
(
×
2)
Pump with Flange
Drive Belt
Replacing Drive Belt
Remove three belt covers as shown.
Remove the belt cover for gearbox pulley.
Disassemble the two M10
×
25 bolts, spring
washers and flat washers, remove the pump
with flange.
Turn the gearbox pulley and pull out the belt.
Lubrication
The gearbox is pre-lubricated and sealed
at the factory. No need to lubricate until 50
hours use.
After first 50 hours use, change all the
transmission oil. Capacity is 1.5L.
For future use, just check the oil level every 50
hours of working. If remove the drain plug, no
oil flow out, then add the oil.
Use portable tool lithium #0 grease such as
Lubriplate 6300AA , Lubriplate GR-132, or
Multifak, e.g. EP-O.
Transmission oil must be replace when engine
is stopped and warm by unscrewing filler cap
and drain plug. When oil is completely drained,
replace filler cap and fill up with fresh oil.
Oil Filler
Oil Outlet
09735UK00M110.indd 16
2017/12/20 16:56:47
Lubrication
The gearbox is pre-lubricated and sealed at the factory. No need
to lubricate until 50 hours use.
After first 50 hours use, change all the transmission oil. Capacity is
1.5 l.
For future use, just check the oil level every 50 hours of working. If
remove the drain plug, no oil flow out, then add the oil.
Use portable tool lithium #0 grease such as Lubriplate 6300AA ,
Lubriplate GR-132, or Multifak, e.g. EP-O.
Transmission oil must be replace when engine is stopped and
warm by unscrewing filler cap and drain plug. When oil is
completely drained, replace filler cap and fill up with fresh oil.
Hydraulic oil
Unscrew the locking nut to drain the oil into the pan.
MINI TRACKED DUMPER
17
GB
Oil Drain Hose
Oil Filler
Remove the oil dipstick and add the oil. The
recommended hydraulic oil is 10W AW32,
ASLE H-150, or ISO 32. Tank Capacity is 3L.
Hydraulic Oil
Unscrew the locking nut to drain the oil into
the pan.
Tightening Tracks
With use, tracks tend to loosen. When
operating with loose tracks, they tend to slip
over the driving wheel causing it to jump its
housing, thus damaging wear to the housing.
To check track tightness, proceed as follows.
1. Set the machine on a flat surface with
compact ground, or on asphalt or pavement.
2. Lift the machine and set it on blocks or
supports rated for the weight of the machine
so that the tracks are approximately 10 cm
off the ground.
3. Measure the track midline vs. the horizontal
line. The reading must not be more than 10
~ 15 mm.
10 ~ 15 mm
If the distance is greater, proceed as follows.
1. Use the tipping handle to tip the hopper
and set it on blocks or supports rated for
the weight of the box.
2. Loosen locknut A.
3. Tighten bolt B until the correct tightness is
restored.
4. Secure bolt B by tightening locknut A
thoroughly.
5. Return the hopper to its original position.
09735UK00M110.indd 17
2017/12/20 16:56:51
MINI TRACKED DUMPER
17
GB
Oil Drain Hose
Oil Filler
Remove the oil dipstick and add the oil. The
recommended hydraulic oil is 10W AW32,
ASLE H-150, or ISO 32. Tank Capacity is 3L.
Hydraulic Oil
Unscrew the locking nut to drain the oil into
the pan.
Tightening Tracks
With use, tracks tend to loosen. When
operating with loose tracks, they tend to slip
over the driving wheel causing it to jump its
housing, thus damaging wear to the housing.
To check track tightness, proceed as follows.
1. Set the machine on a flat surface with
compact ground, or on asphalt or pavement.
2. Lift the machine and set it on blocks or
supports rated for the weight of the machine
so that the tracks are approximately 10 cm
off the ground.
3. Measure the track midline vs. the horizontal
line. The reading must not be more than 10
~ 15 mm.
10 ~ 15 mm
If the distance is greater, proceed as follows.
1. Use the tipping handle to tip the hopper
and set it on blocks or supports rated for
the weight of the box.
2. Loosen locknut A.
3. Tighten bolt B until the correct tightness is
restored.
4. Secure bolt B by tightening locknut A
thoroughly.
5. Return the hopper to its original position.
09735UK00M110.indd 17
2017/12/20 16:56:51
Remove the oil dipstick and add the oil. The recommended
hydraulic oil is 10W AW32, ASLE-H150 or ISO 32. Tank
capacity is 3 liter.
copyrighted
document
- all
rights
reserved
by
FBC