manualshive.com logo in svg

Buell 2008 XB SERIES, Руководство по электрической диагностике, Страница: 92 / 288

Поделиться
Скачать
Buell 2008 XB SERIES Скачать руководство пользователя страница 92

2.15

FUEL PRESSURE TEST

INSPECTION

TOOL NAME

PART NUMBER

FUEL PRESSURE GAUGE ADAPTER

B-45522

FUEL PRESSURE GAUGE

HD-41182

To prevent spray of fuel, purge system of high-pressure
fuel before supply line is disconnected. Gasoline is
extremely flammable and highly explosive, which could
result in death or serious injury. (00275a)

1.

Remove airbox. See the appropriate Buell Service Manual.

2.

Purge the fuel supply line of high pressure gasoline.

a.

See 

Figure 2-35

. Disconnect the 4-place fuel pump

connector [86]. The connector is located inside the
left rear portion of the fuel tank/frame.

b.

With the motorcycle in neutral, start the engine and
allow vehicle to run.

c.

When the engine stalls, press the starter button for 3
seconds to remove any remaining fuel from fuel line.

Wipe up spilled fuel and dispose of rags in a suitable
manner. An open spark around gasoline could cause a
fire or explosion, resulting in death or serious injury.
(00518b)

3.

Figure 2-38

 Depress button (2) of fuel line connector and

disconnect the fuel line (3) from throttle body inlet (1).

4.

See 

Figure 2-39

. Attach FUEL PRESSURE GAUGE

ADAPTER (Part No. B-45522) (2) to throttle body inlet (1).

5.

Connect the fuel line (3) to fuel pressure gauge adapter.

NOTE

See 

Figure 2-40

. Verify that fuel valve (2) and air bleed petcock

(5) on the gauge are closed.

6.

Attach FUEL PRESSURE GAUGE (Part No. HD-41182)
(4) to fuel pressure gauge adapter (1).

7.

See 

Figure 2-35

. Attach fuel pump connector [86] to main

wiring harness.

8.

See 

Figure 2-40

. Pressurize the fuel system.

a.

Start and idle engine to pressurize the fuel system.

b.

Open fuel valve (2) on fuel pressure gauge to allow
fuel to flow down the gauge hose.

c.

Position the air bleed tube (3) into proper container.

d.

Open and close the air bleed petcock (5) to purge the
fuel pressure gauge and hose of air. Repeat this step
several times until only solid fuel (without bubbles)
flows from the air bleed tube.

e.

Close the air bleed petcock.

9.

Open throttle and increase engine speed to 2500-3000
RPM. Note the reading on the pressure gauge.

a.

If pressure is  49-51 PSI (338-352 kPa) then system
is operating within limits.

b.

If pressure is not within limits, see flow chart after
disconnecting pressure gauge.

Wipe up spilled fuel and dispose of rags in a suitable
manner. An open spark around gasoline could cause a
fire or explosion, resulting in death or serious injury.
(00518b)

10. See 

Figure 2-40

. Turn engine off. Detach pressure gauge

(4) from adapter (1).

a.

Open the air bleed petcock (5) to relieve fuel system
pressure and purge the pressure gauge of gasoline.

b.

Remove adapter from vehicle.

11. Detach adapter from vehicle.

12. Connect fuel line to throttle body inlet.

ed01531

Figure 2-35. Fuel Pump Connector [86] (Ulysses - swingarm

removed for illustration)

2-42  2008 Buell XB Diagnostics:  Engine Management

Содержание 2008 XB SERIES

































































































































































































































































































Отзывы:

Нет отзывов