BTEK DD 700 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 34

background image

6

INSTALLATION MANUAL DD700

Removing the weights in inverse order samples the descent.
The procedure (indicated on the display) is the same as for sampling the Full
Scale Zero, with the only difference that, in this case, more than one point must
be sampled.

Zero sampling

Zero sampling is necessary whenever the scale has already been calibrated and
the zero value has moved when the unit switches on. This can happen when the
preset tare is not known exactly at the moment of the first sampling, or when an
unexpected weight is on the scale. No sample weight needs to be available.

The procedure to follow is indicated on the display.

Inverse
sampling

Inverse sampling can be useful in some cases when it is difficult to load and
unload the known weight from the weighing device, for example in hoppers or
batching systems.

The procedure to follow is indicated on the display.

1.3.2

Setup Menu/Scale/Sampling/View data

See the Customisation chapter in the advanced user manual.

1.3.3

Setup Menu/Scale/Sampling/Correction

This option allows you to correct sampling without needing to repeat the procedure.
Depending on the data available, the correction can be calculated in the different ways explained
below.

Weight

Editor

If known, the weight correction can be set directly.
The set value must be within the range:
- (Capacity/100) <Weight < + (Capacity/100)

Gravity

Editor

sampling site

By  selecting  Campogalliano  (headquarters  of  the  Manufacturer)  the  gravity
acceleration  value  of  Campogalliano  (9.80552  m/s)  is  set  automatically.
Otherwise  you may set a gravity acceleration value within the range (9.60000 ÷

10.00000) m/s

.

.

destination site

Knowing the gravity acceleration of the sampling site, you must know the gravity

acceleration  of  the  destination  site  to  calculate  the  weight  correction.  You  may
set a value within the range (9.60000 ÷ 10.00000) m/s.
Otherwise,  the  gravity  acceleration  value  can  be  set  as  the  Coordinates  of  the
destination site: latitude (0 ÷ 90)° and altitude (-1000 ÷ +9000) m.
Based  on  the  data  entered,  the  program  calculates  the  weight  correction  and
enters the value obtained in the Weight parameter.

«
...
6
7
8
9
10
...
»

Содержание DD 700



































Отзывы:

Нет отзывов

Похожие инструкции для DD 700

Бренд: Scarlett Страницы: 35

Бренд: T Scale Страницы: 40

Бренд: Kalorik Страницы: 28

Бренд: Pitney Bowes Страницы: 52

PLATINE BC1500V0

Бренд: TEFAL Страницы: 2

ADVENTURER PRO Series

Бренд: U-Line Страницы: 8

DL2-E Dura-Lift

Бренд: Integrated Visual Data Technology Страницы: 12

Бренд: ADE Страницы: 4

Бренд: A&D Страницы: 116

Бренд: Scarlett Страницы: 8

Бренд: Scarlett Страницы: 16

Бренд: Scarlett Страницы: 9

Бренд: Scarlett Страницы: 10

Бренд: Scarlett Страницы: 19

Бренд: MyWeigh Страницы: 3

Бренд: OK. Страницы: 17

Бренд: Salter Страницы: 8

Бренд: Salter Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды