background image

Bob's Space Racers

®   

Whac-A-Mole

®

 Arcade Games   

BSR MEDIUM AIR COMPRESSOR SAFETY INFORMATION  

* WARNING *  

ALL  ELECTRICAL  WORK  SHOULD  BE  DONE  BY  A 
LICENSED, OR CERTIFIED, ELECTRICIAN.  ON A PROPERLY 
WIRED  CIRCUIT,  THE  BLACK  WIRES  CARRY  THE 
ELECTRICAL CURRENT. 
 

1.

 

Carefully  read  the  instruction  manual  for  each  component  prior  to  attempting  to  assemble, 
disassemble, or operate your system.  

2.

 

Do not exceed the pressure rating of any component in this system.  

3.

 

Protect  material  lines  and  air  lines  from  damage  or  puncture.   Keep  hose  and  power  cable 
away from sharp objects, chemicals, oil, and other solvent spills, and wet floors.  

4.

 

Never  point  a  spray  gun  at  yourself,  or  anyone  else.   Accidental  discharge  may  result  in 
serious injury.  

5.

 

Check hoses for weak or worn areas before each use; make certain all connections are secure; 
do not use is deficiency is found.  

6.

 

Release all pressures within system slowly; dust and debris expelled at high speeds may be 
harmful.  

* WARNING *  

DISCONNECT  POWER  AND  DEPRESSURIZE  SYSTEM 
BEFORE 

SERVICING 

AIR 

COMPRESSOR!  

(TURN 

PRESSURE  REGULATOR  KNOB  FULLY  CLOCKWISE 
AFTER SHUTTING OFF COMPRESSOR.) 
 

7.

 

Follow  all  local  electrical  and  safety  codes,  as  well  as  the  National  Electrical  Code 
(NEC) and the Occupational Safety and Health Act (OSHA).  

8.

 

Wiring  and  fuses  should  follow  electrical  codes,  current  capacity,  and  be  properly 
grounded.  

9.

 

Electrical motors must be securely and adequately grounded.   
(See Grounding Instructions in this manual.)  

Содержание Whac-a-Mole




















































































Отзывы: