BSR Whac-a-Mole Скачать руководство пользователя страница 2

Страница: 2 / 83

Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate frequency energy, and, if not

installed and used in accordance with the instruction manual may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his/her

own expense.

* * *

W A R N I N G :

ALL OF BOB S SPACE RACERS

GAMES ARE SHIPPED WITH THE SAME KEY AND LOCK

SETS.

IT IS IN YOUR BEST INTEREST TO CHANGE THE KEYS AND LOCKS ON YOUR
GAMES WHEN YOU RECEIVE THEM.

Содержание Whac-a-Mole




















































































Результаты поиска

Содержание Whac-a-Mole

Отзывы:

Похожие инструкции для Whac-a-Mole

Бренды по названию

Популярные бренды

BSR Whac-a-Mole, Руководство пользователя

Результаты поиска

Содержание Whac-a-Mole

Отзывы:

Похожие инструкции для Whac-a-Mole

Бренды по названию

Популярные бренды