BSR Whac-a-Mole Скачать руководство пользователя страница 40

Страница: 40 / 83

Bob's Space Racers

Whac-A-Mole

Arcade Games

TROUBLESHOOTING: 2400 ELECTRONICS

(CONTINUED)

PROBLEMS/CAUSES

PROBLEMS WITH THE GAME
Unit Coins Up By Itself

Wire in the Wrong Place

Wrong Register Setting

Credit Display Board Will Not Accept
Changes From the Front Panel Board

Bad Connection

Bad Board

Bad IC

FRONT PANEL BOARD WILL NOT
ALLOW

YOU

CHANGE

REGISTER SETTINGS

No Power

No Connection

Bad Board

No Sound

No Connection

SUGGESTED FIX

Check wiring to the 20-pin connector on the
front panel board for their proper locations.

Check  appropriate  register  for  number  of
tries  per  credit.   See  OPTION  REGISTER
SHEET (in section above this).

Check ribbon cables from credit display
board back to the main board.

Swap board with another one that is known
to be good.

Change 2803 IC next to front panel
connector on the 2400 board.

Check voltage on the 4-pin Molex plug for
12V DC.

Check ribbon cable on the left side of the
board back to the 2400 board.

Swap board with another one that is known
to be good.

Check wiring from the speaker to the 2400
board.

Содержание Whac-a-Mole




















































































Результаты поиска

Содержание Whac-a-Mole

Отзывы:

Похожие инструкции для Whac-a-Mole

Бренды по названию

Популярные бренды

BSR Whac-a-Mole, Руководство пользователя

Результаты поиска

Содержание Whac-a-Mole

Отзывы:

Похожие инструкции для Whac-a-Mole

Бренды по названию

Популярные бренды