Bryston SP 1 Series Скачать руководство пользователя | Manualshive

Страница: 3 / 28

background image

INTRODUCTION

Congratulations on your purchase of the Bryston SP1
precision pre-amplifier/digital processor-decoder.This product
will provide you with the finest available signal control and
DSP audio processing available. Like all Bryston products the
SP1 has been carefully designed and engineered to deliver a
lifetime of enjoyment.

Because the SP1 offers both pre-amplifier and digital decoding
functions it is very important that you thoroughly read this
manual BEFORE you install and use the SP1.

UNPACKING AND ELECTRICAL SAFETY

Your SP1 was carefully packed at the factory to protect
against any damage in shipping and handling. Carefully
examine the packing and the unit for any signs of external
damage or impact and report those to your dealer or Bryston
prior to using the unit.

ACCESSORIES

In the carton you should have found the following accessories
in addition to the SP1:

The Bryston Safety Manual
1 IEC standard power cord
1 SP1 Infrared Remote Control unit with backlight
1 9V Battery for the remote - must be installed

It is VERY IMPORTANT that you read and completely understand the
Safety Manual before installing or connecting the SP1 to any electrical
power source.

1

«
1
2
3
4
5
...
»

Содержание SP 1 Series





























Отзывы:

Нет отзывов

Похожие инструкции для SP 1 Series

Бренд: Magnatone Страницы: 5

Бренд: Warwick Страницы: 1

Бренд: Warwick Страницы: 4

Rampage AXTM-600

Бренд: Audiovox Страницы: 12

Бренд: DR. Z Amplification Страницы: 6

Бренд: Kicker Страницы: 20

S-3 Anniversary

Бренд: Gold Note Страницы: 13

Subamp SBA-12000

Бренд: Lynx Страницы: 12

GTR-7535/104/102

Бренд: JBL Страницы: 38

Бренд: Revox Страницы: 9

MOON Evolution MC-8

Бренд: Simaudio Страницы: 11

Бренд: audiophony Страницы: 5

Бренд: Kustom Страницы: 8

Бренд: Biamp Страницы: 5

427 SMALL BLOCK

Бренд: Ashdown Страницы: 12

PHONO 1 PHONOSTAGE

Бренд: Sonic Frontiers Страницы: 12

q1000 Power Amp

Бренд: DV Mark Страницы: 12

SMARTSTEP Junior R7D-ZP

Бренд: Omron Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды