BRP 2013 Spyder RT Скачать руководство пользователя

Страница: 138 / 191

MAINTENANCE PROCEDURES

Drive Belt

Visually inspect belt alignment and
condition before each ride.

Belt alignment and deflection adjust-
ment should always be performed by
an authorized Can-Am roadster dealer
according

the

MAINTENANCE

SCHEDULE

Drive Belt Alignment

The gap between the belt and the
sprocket internal flange should be
a minimum of 0.5 mm (.02 in).

belt goes beyond the outside edge
of sprocket, have the belt properly
aligned by an authorized Can-Am road-
ster dealer as soon as possible.

rmo2008-001-027_a

BELT ALIGNMENT

1. Rear sprocket teeth
2. Belt
3. Sprocket internal flange
4. Proper belt alignment
5. Belt exceeding external edge – have aligned

A. MIN. 0.5 mm (.02 in)

Drive Belt Wear

Inspect the drive belt with the vehicle
in neutral, engine off, on a level surface
with plenty of room — you will have to
roll the vehicle forward or backward to
see the full length of the belt.

rmo2008-001-109_a

DRIVE BELT SURFACES

1. Outer surface
2. Teeth side surface
3. Tooth

Inspect for the following conditions:

WEAR CONDITION

REQUIRED

ACTION

Good condition

None

Hairline cracks

Monitor

condition

Minor chipping

Monitor

condition

Opened cracks

Replace belt

Hook wear

Replace belt

Missing teeth

Replace belt

136

______________

Содержание 2013 Spyder RT
































































































































































































Результаты поиска

Содержание 2013 Spyder RT

Отзывы:

Похожие инструкции для 2013 Spyder RT

Бренды по названию

Популярные бренды

BRP 2013 Spyder RT, Руководство оператора

Результаты поиска

Содержание 2013 Spyder RT

Отзывы:

Похожие инструкции для 2013 Spyder RT

Бренды по названию

Популярные бренды